Blade - Remove and Install
Removal Procedure
- Position the upper structure to the 45° angle, as shown above.
Show/hide table
Illustration 1 | g00575012 |
- Use a suitable lifting strap to support the blade cylinder.
Show/hide table
Illustration 2 | g00575085 |
- Remove bolt (1) and spacer (2) .
- Remove pin assembly (3) from the blade cylinder with a brass punch.
- Use a suitable strap to lower blade cylinder (4) to the floor.
Show/hide table
Illustration 3 | g00575089 |
- Use the suitable lifting straps to support the blade, as shown above.
Show/hide table
Illustration 4 | g00575092 |
- Remove bolt (5) and spacer (6) .
- Remove pin assembly (7) from the upper structure with a brass punch.
- Repeat Steps 7 and 8 for the other side of the blade.
- Use the suitable lifting straps to remove blade (8) from the undercarriage frame. Weight of the blade is 86 kg (190 lb).
Installation Procedure
Note: Be sure that the pin assembly and the pin bores are thoroughly clean prior to installation of the blade.
- Position the upper structure to a 45° angle, as shown above.
Show/hide table
Illustration 5 | g00575012 |
- Apply a thin coat of 1P-0808 Multipurpose Grease on the diameter of the pin bore and the pin assembly.
Show/hide table
Illustration 6 | g00575092 |
- Install blade (8) to the undercarriage frame with the suitable lifting straps. Weight of the blade is 86 kg (190 lb).
- Install pin assembly (7), spacer (6), and bolt (5) to the blade. Tighten the bolt.
- Repeat Step 4 for the other side of the blade.
- Use a suitable lifting strap to position blade cylinder (4) into the blade.
Show/hide table
Illustration 7 | g00575089 |
- Install pin assembly (3), spacer (2), and bolt (1) to the blade cylinder. Tighten the bolt.
Show/hide table
Illustration 8 | g00575085 |
Caterpillar Information System:
3054 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
M318 and M320 Excavators Machine Electronic Control System Sensors
302.5 Mini Hydraulic Excavator Engine Supplement Engine - Install
302.5 Mini Hydraulic Excavator Engine Supplement Engine - Remove
307B Excavator Supplement for 4M40 Engine Fuel Priming Pump - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Muffler - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Hydraulic Oil Cooler - Install
302.5 Mini Hydraulic Excavator Engine Supplement Hydraulic Oil Cooler - Remove
302.5 Mini Hydraulic Excavator Engine Supplement Water Temperature Regulator - Remove and Install
302.5 Mini Hydraulic Excavator Engine Supplement Water Pump - Remove and Install
307B Excavator Machine Systems Stick Cylinder - Disassemble
302.5 Mini Hydraulic Excavator Engine Supplement Fuel Filter and Water Separator - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Blade Cylinder - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Accumulator (Hydraulic Pilot) - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Bucket - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Bucket Linkage - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Bucket Cylinder - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Stick Cylinder - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Stick - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Boom Cylinder - Remove and Install
5110B Excavator, 24H Motor Grader, 69D, 769D, 773D, 773E, 776D and 777D Off-Highway Truck/Tractors, 771D, 775D and 775E Quarry Trucks and AD40 Series II, AD45 and AE40 II Underground Articulated Trucks Caterpillar Monitoring System Service Meter Mode
302.5 Mini Hydraulic Excavator Machine Systems Boom - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Boom Swing Cylinder - Remove and Install
302.5 Mini Hydraulic Excavator Machine Systems Counterweight - Remove and Install