Inlet and Exhaust Valve Guides - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A (1)     | 9U-6895     | 气门导管冲头     | 1     |
Show/hide table
( 1 ) | 9U-7530 发动机工具总成 的部分工具 |
开始:
- 拆下进气阀和排气阀。 请参阅拆解和组装, "进气阀与排气阀 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 从气门导管 (2) 上拆下气门杆密封 (1) 。
Show/hide table
图 1 | g01003942 |
- 使用工具 (A) 和锤子从缸盖上拆下气门导管。
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A (1)     | 9U-6895     | 气门导管冲头     | 1     |
B (1)     | 9U-6894     | 导向圈     | 1     |
Show/hide table
( 1 ) | 9U-7530 发动机工具总成 的部分工具 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 2 | g01003943 |
- 用清洁的发动机机油润滑气门导管的孔。
- 用工具 (A) 和工具 (B) 将气门导管 (2) 安装到缸盖中,如图所示。
注: 必须使用工具 (B) 将气门导管安装到正确高度。
从缸盖表面到气门导管顶部的高度 ... 35.00 ± 0.50 mm (1.378 ± 0.020 in)
注: 有关详细信息,请参阅规格缸盖, "气门"。
- 将气门杆密封 (1) 安装到气门导管上。
End By: 安装进气阀和排气阀。 请参阅 拆解和组装, "进气阀与排气阀 - 拆卸和安装"。
Caterpillar Information System:
3406E On-Highway Engine Vibration Damper and Pulley - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Flywheel Housing - Remove and Install
3612 and 3616 Engines Fuel Injector - Heavy Fuel Oil
3176C and 3196 Industrial Engines Flywheel - Install
3406E On-Highway Engine Cylinder Head - Install
G3300 Engines Starting the Engine
3176C and 3196 Engines For Caterpillar Built Machines Flywheel - Remove
G3300 Engines Before Starting Engine
3406C Engines for Caterpillar Built Machines Service Meter
3176C and 3196 Engines For Caterpillar Built Machines Water Temperature Regulator - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Water Pump - Install
3176C and 3196 Engines For Caterpillar Built Machines Water Pump - Remove
3406E On-Highway Engine Inlet and Exhaust Valves - Remove and Install
C-18 Truck Engines Compression Brake - Inspect/Adjust
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Remove
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Install
3116 and 3126 Marine Engines Engine Oil Level Gauge - Calibrate
G3300 Engines Actuator Control Linkage - Lubricate
3406E, C-10 and C-12 Truck Engines Compression Brake - Inspect/Adjust
3406C Engines for Caterpillar Built Machines Connecting Rod - Connecting Rod For One-Piece Aluminum Piston
3176C and 3196 Industrial Engines Water Outlet Manifold - Remove
3176C and 3196 Industrial Engines Water Outlet Manifold - Install
3612 and 3616 Engines Fuel Injector Mechanism
3606 and 3608 Engines Engine Design