Fuel Injector - Heavy Fuel Oil
Show/hide table
图 1 | g00526352 |
(1) 卡箍的顶面必须与缸盖的顶面平行,公差为以下值。 ... 2.0 mm (0.08 inch)
(2) 将固定卡箍的锁紧螺母拧紧至以下扭矩。 ... 35 ± 5 N·m (26 ± 4 lb ft)
(3) 用以下扭矩将螺柱拧进缸盖中。 ... 50 ± 5 N·m (37 ± 4 lb ft)
(4) 喷油器齿条
(5) 缸盖内冷却液端口
(6) 密封件。
使用以下步骤安装喷油泵。
- 将 1P-0808 多功能润滑脂 涂在缸盖的孔中以润滑 O 形密封圈。
注: 密封圈 (6) 锯齿形的部分不能与喷油泵的平面对齐。 密封圈 (6) 锯齿形的部分不能与缸盖 (5) 内的冷却液端口对齐。
- 将喷油器放入缸盖孔径中。 使用螺栓和卡箍将喷油器推入正确的位置。
注: 不要敲击喷油泵的顶面,以防将喷油器敲进入缸盖中。
- 拧紧螺柱 (3) 至缸盖。
- 将固定卡箍的锁紧螺母 (2) 拧紧至指定扭矩。
- 拧紧卡箍后,齿条 (4) 必须能够自由移动。
Caterpillar Information System:
3176C and 3196 Industrial Engines Flywheel - Install
3406E On-Highway Engine Cylinder Head - Install
G3300 Engines Starting the Engine
3176C and 3196 Engines For Caterpillar Built Machines Flywheel - Remove
G3300 Engines Before Starting Engine
3406C Engines for Caterpillar Built Machines Service Meter
3176C and 3196 Engines For Caterpillar Built Machines Water Temperature Regulator - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Water Pump - Install
3176C and 3196 Engines For Caterpillar Built Machines Water Pump - Remove
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Cooler - Install
3406E On-Highway Engine Cylinder Head - Remove
3406C (PEEC III) Truck Engine Alternator
3176C and 3196 Engines For Caterpillar Built Machines Flywheel Housing - Remove and Install
3406E On-Highway Engine Vibration Damper and Pulley - Remove and Install
3406E On-Highway Engine Inlet and Exhaust Valve Guides - Remove and Install
3406E On-Highway Engine Inlet and Exhaust Valves - Remove and Install
C-18 Truck Engines Compression Brake - Inspect/Adjust
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Remove
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Install
3116 and 3126 Marine Engines Engine Oil Level Gauge - Calibrate
G3300 Engines Actuator Control Linkage - Lubricate
3406E, C-10 and C-12 Truck Engines Compression Brake - Inspect/Adjust
3406C Engines for Caterpillar Built Machines Connecting Rod - Connecting Rod For One-Piece Aluminum Piston
3176C and 3196 Industrial Engines Water Outlet Manifold - Remove