Water Pump - Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 检查 O 形密封圈和法兰密封垫的状况。 必要时更换密封圈和密封垫。
Show/hide table
图 1 g00513753 Show/hide table图 2 g01061741 - 将 O 形密封圈安装到水泵 ( 6) 上。 用清洁的发动机机油轻轻地润滑孔。
- 用冷却液润滑 O 形密封圈并且将 O 形密封圈安装在管组件 ( 2) 上。 将管组件 (2) 安装在水泵 ( 6) 上。
- 将水泵 (6) 和管组件 ( 2) 定位在前壳体内。 安装螺栓 (10) 和垫圈。 拧紧螺栓至扭矩为
28 ± 7 N·m (21 ± 5 lb ft) 。 - 将法兰密封垫定位在管组件 ( 2) 和水温调节器壳体之间。 安装螺栓 (1) 和垫圈。 拧紧螺栓至扭矩为
28 ± 7 N·m (21 ± 5 lb ft) 。 - 安装软管 (5),然后拧紧软管卡箍 ( 4)。
- 将新电缆带 (3) 放在管组件 ( 2) 上以便固定线束组件。
- 将螺栓 (9) 和垫圈安装到交流发电机支架中。
- 安装油位表 (7) 以及螺栓 ( 8) 和垫圈。
- 向冷却系统再次加注冷却液。 请参阅操作和保养手册 , "冷却系统冷却液(ELC)- 更换"。
结束:
- 安装发动机机油冷却器。 请参阅拆解和组装 , "机油冷却器 - 安装"。
- 安装皮带张紧装置。 请参阅拆解和组装皮带 , "张紧装置 - 拆卸和安装 "。
- 安装交流发电机。 请参阅拆解和组装 , "交流发电机 - 拆卸和安装" 。
Caterpillar Information System:
3176C and 3196 Engines For Caterpillar Built Machines Water Pump - Remove
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Cooler - Install
3406E On-Highway Engine Cylinder Head - Remove
3406C (PEEC III) Truck Engine Alternator
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Cooler - Remove
3406E On-Highway Engine Turbocharger - Disassemble
3524B Engines for Off-Highway Trucks Engine Cranks but Will Not Start
3176C and 3196 Engines For Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
3116 and 3126 Marine Engines Engine Rating Definitions
3176C and 3196 Engines For Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
3306B Industrial Engine Valve Mechanism Cover - Remove and Install
3608 Engine Fuel Injection Control Linkage
3176C and 3196 Engines For Caterpillar Built Machines Water Temperature Regulator - Remove and Install
3406C Engines for Caterpillar Built Machines Service Meter
G3300 Engines Before Starting Engine
3176C and 3196 Engines For Caterpillar Built Machines Flywheel - Remove
G3300 Engines Starting the Engine
3406E On-Highway Engine Cylinder Head - Install
3176C and 3196 Industrial Engines Flywheel - Install
3612 and 3616 Engines Fuel Injector - Heavy Fuel Oil
3176C and 3196 Engines For Caterpillar Built Machines Flywheel Housing - Remove and Install
3406E On-Highway Engine Vibration Damper and Pulley - Remove and Install
3406E On-Highway Engine Inlet and Exhaust Valve Guides - Remove and Install
3406E On-Highway Engine Inlet and Exhaust Valves - Remove and Install