Vibration Damper and Pulley - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 导向螺柱 (5/8 - 18 NF)     |
1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下风扇传动带。 请参阅操作和维护手册, "皮带 - 检查/调整/更换"。
- 从减振器和皮带轮组件上拆下顶部螺栓 (1) 。 将工具 (A) 安装到螺栓的位置。
Show/hide table
图 1 | g00514084 |
- 拆下剩余的螺栓 (1) 。
- 从曲轴上拆下减振器 (3) 。
- 从曲轴上拆下皮带轮 (2) 。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 导向螺柱 (5/8 - 18 NF)     |
1     |
B     | 4C-5593     | 防粘结剂     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
彻底接触粘滞减振器是否有漏油或外壳凹陷(损坏)的迹象。 这两个情况中的任何一个都可能导致重块与外壳相接触。 这样会影响粘滞减振器的操作。 |
- 将工具 (A) 安装到曲轴顶部的螺栓孔中。
Show/hide table
图 2 | g00514084 |
- 将皮带轮 (2) 和减振器 (3) 安装到曲轴上。
- 将工具 (B) 涂抹在螺栓 (1) 上。 安装螺栓 (1) 。
- 拆下工具 (A) 。 安装螺栓 (1) 来代替工具 (A) 。
- 安装风扇传动带。 请参阅操作和维护手册, "皮带 - 检查/调整/更换"。
Caterpillar Information System:
3176C and 3196 Engines For Caterpillar Built Machines Flywheel Housing - Remove and Install
3612 and 3616 Engines Fuel Injector - Heavy Fuel Oil
3176C and 3196 Industrial Engines Flywheel - Install
3406E On-Highway Engine Cylinder Head - Install
G3300 Engines Starting the Engine
3176C and 3196 Engines For Caterpillar Built Machines Flywheel - Remove
G3300 Engines Before Starting Engine
3406C Engines for Caterpillar Built Machines Service Meter
3176C and 3196 Engines For Caterpillar Built Machines Water Temperature Regulator - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Water Pump - Install
3176C and 3196 Engines For Caterpillar Built Machines Water Pump - Remove
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Cooler - Install
3406E On-Highway Engine Inlet and Exhaust Valve Guides - Remove and Install
3406E On-Highway Engine Inlet and Exhaust Valves - Remove and Install
C-18 Truck Engines Compression Brake - Inspect/Adjust
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Remove
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal - Install
3116 and 3126 Marine Engines Engine Oil Level Gauge - Calibrate
G3300 Engines Actuator Control Linkage - Lubricate
3406E, C-10 and C-12 Truck Engines Compression Brake - Inspect/Adjust
3406C Engines for Caterpillar Built Machines Connecting Rod - Connecting Rod For One-Piece Aluminum Piston
3176C and 3196 Industrial Engines Water Outlet Manifold - Remove
3176C and 3196 Industrial Engines Water Outlet Manifold - Install
3612 and 3616 Engines Fuel Injector Mechanism