A New Water Spray Nozzle has been Added to the Chamber{5612, 6635}
- Cold Planer:
- PM-465 (S/N: 5ZS139-182)
Introduction
This Special Instruction provides information in order to prolong the life of the cutting bits on the PM-465 rotor.
An additional spray nozzle was added to the left side of the chamber.
Rework Procedure
Show/hide table
Required Parts     | ||
Quantity     | Part Number     | Description     |
1     | 211-8607     | Tube     |
1     | 211-8604     | Plate     |
1     | 1G-6699     | Adapter     |
1     | 1G-8270     | Nozzle Body     |
2     | 5D-1026     | Hose Clamp     |
1000 mm (39 inch)     | 5P-1690     | Hose     |
1     | 081-2963     | Cap     |
1     | 081-2965     | Seal     |
1     | 115-9969     | Male Connector     |
1     | 115-9970     | Male Connector     |
1     | 212-0911     | Nozzle     |
- Remove 142-7461 Plate (1) from the chamber.
Show/hide table
Illustration 1 | g00853436 |
(A) 573 mm (22.56 inches) (B) 102.5 mm (4 inches) (C) 150 mm (5.91 inches) |
- Relocate the 142-7461 Plate (1) .
- The new location of the 142-7461 Plate (1) should measure 150 mm (5.91 inches) (C) from the top of the chamber. The center of the 142-7461 Plate should remain at 573 mm (22.56 inches) (A) .
- Cut a slot in the left side of the chamber that is 40 mm (1.57 inch) by 85 mm (3.35 inch). The center of the slot should measure 102.5 mm (4 inches) from the top (B) of the chamber and 573 mm (22.56 inches) from the front (A) of the chamber. Refer to Illustration 1.
- Weld the 211-8604 Plate (2) in the slot. The plate should be flush with the inside of the chamber. Face the open end of the plate downward in the slot.
Show/hide table
Illustration 2 | g00853889 |
- Weld a 211-8607 Tube (3) onto the side of the chamber. Position the bottom of the tube 20 mm (0.79 inch) (D) from the bottom of the slot and 8.5 mm (0.33 inch) (E) to the right of the slot. Refer to Illustration 4.
Show/hide table
Illustration 3 | g00853468 |
Show/hide table
Illustration 4 | g00853890 |
(D) 20 mm (0.79 inch) (E) 8.5 mm (0.33 inch) |
- Remove hose assembly (4) from the nozzle (5) that is located near the left side of the chamber.
Show/hide table
Illustration 5 | g00853470 |
- Replace connector (6) with 115-9970 Male Connector .
- Use the following parts in order to assemble a new nozzle: 115-9969 Male Connector (7), 1G-6699 Adapter (8), 1G-8270 Nozzle Body (9), 212-0911 Nozzle (10), 081-2965 Seal (11) and 081-2963 Cap (12) .
Show/hide table
Illustration 6 | g00863254 |
- Place the new nozzle assembly in tube (13) that is located on the side of the chamber.
Note: The flat spray pattern of the nozzle should be parallel to the slot.
Show/hide table
Illustration 7 | g00853509 |
Caterpillar Information System:
CB-634D Vibratory Compactor Machine Systems Brake and Shift Valve - Remove
14H Motor Grader Transmission and Differential Oil Filter and Screens - Replace/Clean
834G Wheel Tractor and 836G Landfill Compactor Engine Supplement Fan Shroud - Install
CB-634D Vibratory Compactor Machine Systems Gear Pump (Steering) - Install
773E Off-Highway Truck Power Train Differential and Bevel Gear
14H and 16H Motor Graders Air System and Brakes Air Compressor
69D, 73D, 769C, 769D, 773B, 773D, 773E, 776B, 776C, 776D, 777B, 777C, 777D, 784B, 785, 785B, 789 and 793 Off-Highway Truck/Tractors and 771D, 775B, 775D and 775E Quarry Trucks Payload System Wiring Harness (Short Circuit) - Test
69D, 73D, 769C, 769D, 773B, 773D, 773E, 776B, 776C, 776D, 777B, 777C, 777D, 784B, 785, 785B, 789 and 793 Off-Highway Truck/Tractors and 771D, 775B, 775D and 775E Quarry Trucks Payload System Wiring Harness (Open Circuit) - Test
14H Motor Grader Transmission and Differential Oil - Change
2002/10/07 A New Seal with Increased Serviced Life is Used in the Front Suspension Cylinder {7200, 7201}
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
CB-634D Vibratory Compactor Machine Systems Gear Pump (Steering) - Remove
120H and 135H Motor Graders Ripper Cylinder Bearings - Lubricate
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Remote Direction Control
CB-634D Vibratory Compactor Machine Systems Brake and Shift Valve - Install
Instructions for Updating the CABSWin Software and for Reinstalling the CabsWin Software{7620} Instructions for Updating the CABSWin Software and for Reinstalling the CabsWin Software{7620}
CB-634D Paving Compactor Water Spray System - Drain
CB-634D Vibratory Compactor Machine Systems Vibratory Valve - Remove
CB-634D Paving Compactor Water Spray System Filter - Clean
CB-634D Paving Compactor Water Tank Strainer - Clean and Inspect
CB-634D Vibratory Compactor Machine Systems Vibratory Valve - Install
CB-634D Vibratory Compactor Machine Systems Brake Pump - Remove and Install
2002/01/21 Changes to the Rear Spindle and to the Bearing Cone {4208, 4234, 7551}
834G Wheel Tractor and 836G Landfill Compactor Engine Supplement Radiator Top Tank - Install