Aftercooler - Remove
开始:
- 放出后冷器芯中的冷却液。 请参考操作和保养手册, "冷却系统冷却液 - 更换"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 拆下螺栓 (5)、垫圈和隔套。
- 从夹子上拆下螺栓 (2) 和垫圈。
- 断开燃油管 (1)。 立即在全部阳接头上加装保护盖,在所有阴接头上加装螺塞。
- 拆下螺栓 (3)。 拆下弯头 (4)。
Show/hide table
图 2 g00579403 典型实例 - 断开燃油管 (8)。 立即在全部阳接头上加装保护盖,在所有阴接头上加装螺塞。
- 拆下螺栓 (7)。 拆下安全阀壳体 (6)。
Show/hide table
图 3 g00579404 典型实例 - 拆下螺栓 (9)。 拆下弯头 (10) 和 O 形密封圈。
- 拆下螺栓 (13) 和垫圈。
- 拆下夹子 (12) 和支架 (11)。
- 拆下后冷器端盖 (14) 和密封垫。
Show/hide table
图 4 g00579407 典型实例 - 拆下螺栓 (15) 和垫圈。
Show/hide table
图 5 g00579409 典型实例 - 拆下螺栓 (20)、弯头 (19) 和 O 形密封圈。
- 拆下两个过渡接头 (16) 和 O 形密封圈 (17)。
- 拆下两个过渡接头 (18) 和 O 形密封圈。
Show/hide table
图 6 g00579412 典型实例 - 将适当的起吊设备固定到后冷器芯 (21) 的起重支架上。
- 将后冷器芯从壳体上拆下。
后冷器芯的重量约为
26 kg (57 lb) 。 - 拆下 O 形密封圈 (22)。
Show/hide table
图 7 g00579413 典型实例 - 必要时,拆下螺栓 (24) 和垫圈。 拆下后冷器壳体 (23)。
Show/hide table
图 8 g00579418 典型实例 - 拆下后冷器壳体的密封垫 (25)。
Show/hide table
图 1 | g00579401 |
典型实例 |
- 拆下三个螺栓 (1)。
- 拆下螺栓 (2) 和板。
- 拆下管组件 (3) 和密封垫。
Show/hide table
图 10 g00713974 - 拆下三个螺栓 (4)。
- 拆下螺栓 (5) 和板。
- 拆下管组件 (6) 和密封垫。
Show/hide table
图 11 g00714031 - 将四条螺栓 (7) 从后冷器前端的弯头 (8) 上拆下。
- 将四条螺栓 (9) 从后冷器前端的弯头 (10) 上拆下。
Show/hide table
图 12 g00713977 - 将两条螺栓 (11) 和垫圈从后冷器右侧的支架 (12) 上拆下。
Show/hide table
图 13 g00713992 - 将螺栓 (13) 从右侧后冷器的底部拆下。
Show/hide table
图 14 g00713996 - 将两条螺栓 (14) 和垫圈从后冷器左侧的支架 (15) 上拆下。
- 将螺栓 (16) 从左侧后冷器的底部拆下。
Show/hide table
图 15 g00714001 - 将四条螺栓 (17) 和垫圈从后冷器底部拆下。
Show/hide table
图 16 g00714007 - 拆下螺栓 (18) 和卡箍 (19)。 将软管组件定位到后冷器前端。
Show/hide table
图 17 g00714016 - 利用位置 (A) 的起吊设备拆下后冷器 (20) 及其支架 (12) 和 (15)。 后冷器、支架和剩余冷却液的重量约为
43 kg (95 lb) 。注: 冷却液排放后,部分冷却液会留在后冷器中。 确保冷却液进口高于对面。 这样可以尽量避免冷却液溢出。
Show/hide table图 18 g00714041 - 将 O 形密封圈 (21) 从弯头 (8) 和 (10) 上拆下。
Show/hide table
图 9 | g00713966 |
Caterpillar Information System:
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Machine Does Not Move
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System CID 0190 FMI 02 Speed Sensor (Engine) Incorrect Signal - Test
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train Fixed Axle and Oscillating Axle
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System System Power
2001/11/12 Corrections to Disassembly and Assembly , "Inlet and Exhaust Valve Guides - Remove and Install" {1104}
2001/11/26 Puller Holes Have Been Added to Gear Assemblies for the Transmission {3061}
TH210 and TH215 Telehandlers Power Train General Information
735 Articulated Truck Power Train Rear Axle - Remove
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train Output Transfer Gears
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Pilot Valve (Joystick)
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train Oil Filter (Power Train)
2002/01/21 A New Quick Coupler is Required to Extend the Service Life of Dual Purpose Valves {6129, 7542}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Four)(Mechanically Operated)
3408E and 3412E Engines for Caterpillar Built Machines Aftercooler - Install
950G Series II and 962G Series II Wheel Loaders and IT62G Series II Integrated Toolcarrier Power Train Parking Brake - Remove
950G Series II and 962G Series II Wheel Loaders and IT62G Series II Integrated Toolcarrier Power Train Parking Brake - Install
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Four)(Mechanically Operated)
797 Off-Highway Truck Engine Oil Pan Sump Screen - Inspect/Clean
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train Transmission Planetary
2006/08/14 Changes to the Steer Linkage Improve the Service Life {4305}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Four)(Mechanically Operated)
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Four)(Mechanically Operated)
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System CID 0190 FMI 09 Speed Sensor (Engine) Abnormal Update - Test
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Four)(Mechanically Operated)