Parking Brake - Install
Installation Procedure
Note: Clean all parts and inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install brake actuator mounting bracket (19), the washers, and two nuts (18) .
Show/hide table
Illustration 1 | g00447904 |
- Install the brake camshaft.
- Install plate assembly (17) and four bolts (16). The torque for bolts (16) is 240 ± 40 N·m (180 ± 30 lb ft).
Show/hide table
Illustration 2 | g00447831 |
- Install brake shoes (13), brake adjuster (15), brake retainer spring (14), brace (11) and brake return springs (12) .
Show/hide table
Illustration 3 | g00447806 |
- Install O-ring seal (7), yoke (10), yoke retainer (9) and bolt (8). The torque for bolt (8) is 170 ± 15 N·m (125 ± 11 lb ft).
Show/hide table
Illustration 4 | g00447730 |
- Install brake drum (6), eight bolts (5), and the washers.
Show/hide table
Illustration 5 | g00447703 |
- Install parking brake actuator lever (3) and bolt (4). The torque for bolt (4) is 47 ± 9 N·m (35 ± 7 lb ft).
Show/hide table
Illustration 6 | g00447664 |
- Connect yoke assembly (2) to the parking brake actuator lever (3). Install clevis pin (1) .
- To adjust the parking brake, rotate the brake adjuster until the brake drum cannot be rotated by hand. Then, back off the brake adjuster by six clicks.
End By: Install the center drive shaft. Refer to Disassembly and AssemblyRENR4311, "Drive Shaft (Center) - Remove and Install".
Caterpillar Information System:
950G Series II and 962G Series II Wheel Loaders and IT62G Series II Integrated Toolcarrier Power Train Parking Brake - Remove
3408E and 3412E Engines for Caterpillar Built Machines Aftercooler - Install
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Four)(Mechanically Operated)
3408E and 3412E Engines for Caterpillar Built Machines Aftercooler - Remove
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Machine Does Not Move
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System CID 0190 FMI 02 Speed Sensor (Engine) Incorrect Signal - Test
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train Fixed Axle and Oscillating Axle
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System System Power
2001/11/12 Corrections to Disassembly and Assembly , "Inlet and Exhaust Valve Guides - Remove and Install" {1104}
2001/11/26 Puller Holes Have Been Added to Gear Assemblies for the Transmission {3061}
TH210 and TH215 Telehandlers Power Train General Information
735 Articulated Truck Power Train Rear Axle - Remove
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Four)(Mechanically Operated)
797 Off-Highway Truck Engine Oil Pan Sump Screen - Inspect/Clean
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train Transmission Planetary
2006/08/14 Changes to the Steer Linkage Improve the Service Life {4305}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Four)(Mechanically Operated)
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Four)(Mechanically Operated)
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System CID 0190 FMI 09 Speed Sensor (Engine) Abnormal Update - Test
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Four)(Mechanically Operated)
2001/10/22 Correction to Testing and Adjusting , "Transmission Pressures - Test and Adjust" {3030, 3030}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Four)(Mechanically Operated)
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Machine Operates in Only One Speed Range
416D, 420D, 424D, 428D, 432D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Four)(Pilot Operated)