Center Axle
Show/hide table
Illustration 1 | g00807420 |
(1) Use 1U-8846 Gasket Sealant in order to form a seal at the flange.
(2) Tighten 25 bolts to a torque of 125 ± 25 N·m (90 ± 18 lb ft) in an alternating star pattern. Tighten the bolts again. Final tightening torque for the bolts 270 ± 25 N·m (200 ± 19 lb ft)
(3) Torque at the bolt ... 900 ± 100 N·m (660 ± 74 lb ft)
(4) Torque for bearing locknut ... 200 ± 40 N·m (148 ± 30 lb ft)
(5) Torque for the 4 setscrews ... 7 ± 1 N·m (62 ± 9 lb in)
(6) Tighten 52 bolts to a torque of 430 ± 60 N·m (320 ± 45 lb ft) in an alternating star pattern.
Caterpillar Information System:
735 and 740 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Signal and Pressure Reducing Valve (Steering)
735 Articulated Truck Power Train Front Axle
2001/07/02 Revised Special Instruction, REHS0924-02 , "Installation Procedure for Side Window Wipers on Forwarders" is Available {7305}
2002/03/25 New Slack Adjusters are Used for Improved Service Life {0731, 4261}
PM-465 Cold Planer Steering Control
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Steering System Steering Control Valve - Adjust
3176C and 3196 Engines for Caterpillar Built Machines 5 Volt Engine Pressure Sensor Supply Circuit - Test
8-16B Extend-A-Mat Screed Operating Principles
TK1051 Track Feller BuncherEngine Supplement Preparation for Disassembly
CP-433E, CS-423E and CS-433E Vibratory Compactors Engine Supplement Electric Starting Motor - Remove and Install
2001/07/02 Special Instruction, REHS0986, "Procedure for the Removal of Bolts That Are Used for Shipping on Differentials" is Now Available {3258}
8-16B Extend-A-Mat Screed Screed Plate Leveling
Conversion of the Joystick from Fork Control to Bucket Control{5063, 5705, 6107} Conversion of the Joystick from Fork Control to Bucket Control{5063, 5705, 6107}
2001/07/02 Special Instruction, REHS0977, "Rework Extends Service Life of the Axle" is Available {3278}
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Hydraulic and Steering System Hydraulic Cylinder Drift - Check
2001/08/13 An Improved Unit Injector Hydraulic Pump is Available {1714}
PF-300B and PS-300B Pneumatic Compactors Final Drive Reducer Oil Level - Check
824G Series II Wheel Dozer, 825G Series II Soil Compactor and 826G Series II Landfill Compactor Power Train Pinout Specifications for Electronic Control (Power Train)
69D and 769D Off-Highway Trucks and 771D Quarry Truck Steering System Pressure and Flow Compensator Valve
PF-300B and PS-300B Pneumatic Compactors Final Drive Reducer Oil - Change
735 Articulated Truck Power Train Rear Axle
TK1051 Track Feller Buncher Machine Systems Stick - Install
2001/09/17 New Weld Joints are Used on the Gates of Forwarders {6331}
PF-300B and PS-300B Pneumatic Compactors Tire Mat - Replace