Electric Starting Motor
106-8554, 104-7044, 6v-5795
Show/hide table
Illustration 1 | g00286672 |
Show/hide table
Illustration 2 | g00286673 |
Typical Example |
When the electric starting motor is viewed from the pinion end, the motor rotates in the following direction. ... Clockwise
No load conditions at 25 °C (77 °F)
- Speed ... 7643 ± 1683 rpm
- Current draw ... 67.5 ± 7.5 amp
- Voltage ... 23 V
- Current draw ... 67.5 ± 7.5 amp
(1) Nut
-
Three wires are the maximum that may fit between the nuts.
- Tighten the nut on the battery terminal to the following torque. ... 30.5 ± 3.5 N·m (22 ± 3 lb ft)
(2) Nut
- Tighten the nut on the ground terminal to the following torque. ... 30.5 ± 3.5 N·m (22 ± 3 lb ft)
(3) Nut
- Tighten the nut on the ground terminal to the following torque. ... 2.25 ± 0.25 N·m (20 ± 2 lb in)
(4) Nut
-
The terminal that is on the switch terminal must be insulated with heat shrink tubing.
- Tighten the nut on the switch terminal to the following torque. ... 2.25 ± 0.25 N·m (20 ± 2 lb in)
(5) Nut
- Tighten the nut on the motor terminal to the following torque. ... 30.5 ± 3.5 N·m (22 ± 3 lb ft)
(6) Nut
- Tighten the nut on the motor frame terminal to the following torque. ... 8 ± 3 N·m (71 ± 27 lb in)
Solenoid
Current draw at 20 V and 25 °C (77 °F)
- Pull-in windings ... 56.5 ± 4.5 amp
- Hold-in windings ... 14.6 amp
Caterpillar Information System:
2001/01/08 Replacement of Support Blocks for the Rear Axle and the Center Axle A-Frames Covered in Special Instruction, REHS0931 {3278, 7051}
2000/09/25 The Piston Pump (Propel) and the Piston Pump (Vibratory) have Changed {5070}
527 Track-Type Skidder Engine Supplement Turbocharger - Remove and Install
C-10, C-12, C-15 and C-16 Industrial Engines Diagnostic Codes
Caterpillar Monitoring System Quad Gauge Module
725 and 730 Articulated Trucks Window Washer Reservoir - Fill
TH62, TH63, TH82 and TH83 Telehandlers Steering System Piston Pump (Implement and Steering)
2000/09/04 A Special Instruction Is Available for Installing New Wiring Harnesses on Harvester Heads {5734}
Caterpillar Monitoring System MID 030 - CID 0826 - FMI 08
IT62G Series II Integrated Toolcarrier Indicators
527 Track-Type Skidder Engine Supplement Alternator - Remove and Install
2000/09/04 Pilot Valves Now Have Serviceable O-Rings and Seals {4342}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Axles, Differential and Brakes Axle, Differential and Brake Troubleshooting
CP-663E, CS-663E and CS-683E Vibratory Compactors Backup Alarm
IT62G Series II Integrated Toolcarrier Light Switches
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Hydraulic Tank and Mounting
725 and 730 Articulated Trucks Window Wiper - Inspect/Replace
527 Track-Type Skidder Engine Supplement Water Temperature Regulator - Remove and Install
CP-663E, CS-663E and CS-683E Vibratory Compactors Mirror
Use of Repair Kit for Nonmetallic Fuel Tanks {1273} Use of Repair Kit for Nonmetallic Fuel Tanks {1273}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Axles, Differential and Brakes Axle (Front)
IT62G Series II Integrated Toolcarrier Window Wiper and Washer Control
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader CAT Data Link Circuit - Test
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Axles, Differential and Brakes Drive and Steering Axle (Front)