Window Wiper and Wiper Motor (Front) - Remove and Install
Removal Procedure
Start By:
- Remove the steering column. Refer to Disassembly and Assembly, "Steering Column - Remove and Install".
- Put identification marks on all wire harnesses for installation purposes.
- Lift covers (1). Remove two nuts (2) and two washers (3) in order to remove wiper arms (4) .
Show/hide table
Illustration 1 | g00730388 |
- Remove six screws (5) and ease lower dash panel (6) downward. Disconnect electrical connector (7).
Show/hide table
Illustration 2 | g00730393 |
- Use a second person and support the wiper motor from the inside of the cab. Remove two plastic caps (8), two nuts (9), two plastic washers (10), and two rubber washers (11) .
Show/hide table
Illustration 3 | g00730396 |
- Remove wiper motor (12) .
Show/hide table
Illustration 4 | g00730397 |
Installation Procedure
- Inspect all parts and clean all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
- Install wiper motor (12) into the cab. Use a second person and support the wiper motor.
Show/hide table
Illustration 5 | g00730397 |
- Install two rubber washers (11), two plastic washers (10), two nuts (9) and two plastic caps (8) .
Show/hide table
Illustration 6 | g00730396 |
- Connect electrical connector (7). Position lower dash panel (6) and install six screws (5) .
Show/hide table
Illustration 7 | g00730393 |
- Switch the wiper motor to the ON position. Allow the wiper motor to rotate several times and then switch the wiper motor to the OFF position. The wiper motor will now be in the PARK position.
- Install wiper arms (4) with the wiper blade 25 mm (1 inch) from the left side window seal. Install two washers (3) and two nuts (2). Close two covers (1) .
Show/hide table
Illustration 8 | g00730388 |
Show/hide table
NOTICE |
---|
Push the wiper arm assembly straight onto the tapered shaft. If the wiper arm assembly is not installed straight when the shaft turns, the splines will be improperly formed and damage will occur. |
End By: Install the steering column. Refer to Disassembly and Assembly, "Steering Column - Remove and Install".
Caterpillar Information System:
TH62, TH63, TH82 and TH83 Telehandlers Quick Coupler
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Power Train Transmission (Power Shift) - Disassemble
IT28G and IT38G Integrated Toolcarriers and 924G, 924GZ, 928G and 938G Wheel Loaders Power Train Electronic Control System Remote Direction Control Function
C-9 Engines for Caterpillar Built Machines Flywheel Housing
IT28G and IT38G Integrated Toolcarriers and 924G, 924GZ, 928G and 938G Wheel Loaders Power Train Electronic Control System Ride Control Function
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) TPS Maximum Payload Speed Manager
2000/08/07 A New Engine Shutdown Switch is Available {7418}
2000/07/31 Correction to Parts Manual for the R1300 LHD {7301}
2000/08/07 Revision to Parts Manual for the R2900 LHD {5073}
IT28G and IT38G Integrated Toolcarriers and 924G, 924GZ, 928G and 938G Wheel Loaders Power Train Electronic Control System Electronic Control Module (Autoshift)
2000/08/07 Revision to Parts Manual for the R1700G LHD {5073}
IT28G and IT38G Integrated Toolcarriers and 924G, 924GZ, 928G and 938G Wheel Loaders Power Train Electronic Control System Automatic Shift Function
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Power Train Front Axle - Remove
C-9 Engines for Caterpillar Built Machines Compression Brake
797 Off-Highway Truck Braking System Oil Filter (Brake Actuation)
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders and 247, 257, 267, 277 and 287 Multi Terrain Loaders Interlock Electronic Control System General Information
416D Backhoe Loader Tire Installation
2000/08/28 A New Check Valve Reduces Voiding {5067, 5104}
CB-334D and CB-335D Vibratory Compactors Operating Technique Information
IT28G Integrated Toolcarrier and 928G Wheel Loader Brake and Fan Drive System Gear Motor (Fan Drive)
924G and 924Gz Wheel Loaders Brake and Fan Drive System Gear Pump (Fan Drive and Brakes)
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders and 247, 257, 267, 277 and 287 Multi Terrain Loaders Interlock Electronic Control System Engine Start Interlock
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders and 247, 257, 267, 277 and 287 Multi Terrain Loaders Interlock Electronic Control System Work Tool Interlock
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Power Train Front Axle - Install