Piston Cooling Jet
Note: Piston cooling jets are installed on turbocharged engines only.
Show/hide table
Illustration 1 | g00721168 |
(1) Banjo bolt
- Tighten the banjo bolt for the piston cooling jet to the following torque. ... 27 N·m (20 lb ft)
(2) Piston cooling jet
Alignment
Show/hide table
Required Tools     | ||
Part Number     | Part Name     | Qty     |
FT-2736     | Alignment Gauge     | 1     |
Show/hide table
Illustration 2 | g00712686 |
To align the piston cooling jet, use the following procedure:
- Build an alignment gauge (4) out of 3 mm (0.12 inch) plexiglass. For the correct dimensions, see the print for FT-2736 Alignment Gauge .
- Install the alignment gauge on pins (1) of the cylinder head.
- Insert a rod (2) that is 1.2 mm (0.05 inch) in diameter into each piston cooling jet. The rods must protrude through holes (3) in order for the piston cooling jet to be aligned properly. If the rods do not protrude through the holes in the alignment tool, bend the piston cooling jet. Check the rods again for correct alignment.
- Remove the alignment gauge and the rods.
Caterpillar Information System:
2000/06/05 New Tire Skirt Material is Available {718T}
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Check of Controller LED Indicator - Troubleshoot
CB-535B Vibratory Compactor Propel System Final Drive Planetary
2000/04/03 A New O-ring Seal for the Jacket Water Heater Provides Improved Service Life {1383}
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Harness and Wire Identification
3034 Engine for Caterpillar Built Machines Flywheel Housing
D400E Series II Ejector Truck Safety Signs and Labels
D400E Series II Ejector Truck Caterpillar Monitoring System
D400E Series II Ejector Truck Differential Lock Control
D400E Series II Ejector Truck Ejector Control
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 1089 FMI 12 Analysis Control Module Failed - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 1089 FMI 09 Analysis Control Module Abnormal Update - Test
776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Transmission, Transfer Gears, and Differential - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Nozzle - Test
D400E Series II Ejector Truck Product Identification Number, Serial Number and EU's CE Plate Locations
D400E Series II Ejector Truck Engine Start Switch
2000/04/17 New 160-1728 Differential Bracket Assembly Adapter Provides Support on the Differential Carrier {0717, 3258}
D400E Series II Ejector Truck Hazard Flasher Control
2000/04/24 A 3E-6510 Film with White Letters Is Now Available as a Replacement for 9X-1729 Film . {7557}
D400E Series II Ejector Truck Model View Illustrations
D400E Series II Ejector Truck Heating and Air Conditioning Control
TH62, TH63, TH82, TH83 and TH103 Telehandlers Longitudinal Stability Indicator System Display Module
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0767 FMI 03 Pressure Sensor (Fixed Displacement Pump Oil) Voltage Above Normal - Test
D400E Series II Ejector Truck Indicators