A Guard for the Transmission Breather Can Be Installed {7153}
- Combine:
- Lexion450 (PIN: 8YW1-492)
- Lexion460 (PIN: 9FW1-577)
- Lexion465 (PIN: 3HZ1-505)
- Lexion470 (PIN: 9TW1-401)
- Lexion480 (PIN: 2BZ1-572)
- Lexion485 (PIN: 8ZW1-490)
Description of Change: A guard for the transmission breather has been added to the transmission case. The guard keeps oil from seeping out of the transmission breather.
Adaptable To: The guard may be added to the transmission case of the machines that are listed above. Two holes will need to be added to the inside or bottom of the cover for the transmission in order to secure the guard in place over the transmission breather. Use the following procedure in order to install the guard.
Show/hide table
| Required Parts | |||
|---|---|---|---|
| Item | Part Number | Part Description | Qty |
| A | 188-7876 | Guard | 1 |
| B | 151-9081 | Washer (M6) | 2 |
| C | 161-6266 | Bolt (M6 x 1.0 x 12mm) | 2 |
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Item | Part Number | Part Description | Qty |
| E | 1U-8152 | Drill (5.20mm) | 1 |
| F | 8T-3081 | Tap (M6 x 1.0) | 1 |
| 4C-5027 | Tap Wrench | 1 | |
- Remove the front portion of the preparation floor. Refer to the first six steps of the Disassembly and Assembly, RENR1654, "Preparation Floor - Remove" procedure.
- Remove twelve bolts (1) and top cover (2) of the transmission.
Show/hide table
 | |
| Illustration 1 | g00702815 |
Note: Carefully remove the top cover. Springs are located below the cover.
- Use a drill press and Tool (E) in order to drill two holes in the top cover. The specifications are in Illustration 2. The holes should be drilled from the bottom of the cover. Use Tool (F) in order to tap the two holes for the 161-6266 Bolt (M6 x 1.0 x 12mm).
Show/hide table
 | |
| Illustration 2 | g00691211 |
(X) 9 mm (0.3543 inch) (Y) 39 mm (1.5354 inch) (Z) 28 mm (1.1024 inch) | |
- Install plate (A) on the bottom side of the cover. Apply 4C-9507 Retaining Compound on bolts (C) and washers (B). Install the bolts and washers.
Show/hide table
 | |
| Illustration 3 | g00701165 |
- Verify that the detent springs (5) are in the correct position.
Show/hide table
 | |
| Illustration 4 | g00699886 |
- Install top cover (2) of the transmission and twelve bolts (1) .
Show/hide table
| | |
| Illustration 5 | g00702815 |
- Install the front portion of the preparation floor. Refer to the first six steps of the Disassembly and Assembly, RENR1654, "Preparation Floor - Install" procedure.
Caterpillar Information System:
2000/03/27 Dimensions in Special Instruction are now Updated {3260, 3269, 6116, 6118, 6119, 6125, 6126, 6127, 7057, 7069, 7100}
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes Gear Pump (Torque Converter Charging, Scavenge, and Brake Release)
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes Gear Pump (Torque Converter Charging, Scavenge, and Brake Release)
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0295 FMI 12 Electronic Control Module (Machine) Failed - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0295 FMI 09 Electronic Control Module (Machine) Abnormal Update - Test
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Controller Input and Output Values
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0295 FMI 02 Electronic Control Module (Machine) Incorrect Signal - Test
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Controller - Replace
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Speed Sensor - Replace
793C Off-Highway Truck Throttle Backup Switch
793C Off-Highway Truck Traction Control System (TCS) - Test
CB-534C Vibratory Compactor Fuel System Water Separator Element - Replace
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes Gear Pump (Hoist)
3618 Engine Main Bearings
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes Gear Pump (Pulled Unit)
2000/03/20 A New Indicator Assembly (Voltmeter) {7450}
2000/03/27 Maintenance and Repair to a Closed Loop System for the Engine Crankcase Breather {1107, 1317}
Caterpillar<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> AP-900B andBarber-Greene<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> BG-240C Asphalt Pavers Propel System General Information
Caterpillar<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> AP-900B andBarber-Greene<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> BG-240C Asphalt Pavers Propel System Front Wheel Drive Manifold
D400E Series II Ejector Truck After Starting Engine
D400E Series II Ejector Truck Cold Weather Operation
D400E Series II Ejector Truck Starting Above 0°C (32°F)
D400E Series II Ejector Truck Loading
D400E Series II Ejector Truck Machine Operation Information