Steering Cylinder Bearings - Lubricate
Show/hide table
| NOTICE |
|---|
|
Check that the lines attached to all the remote grease fittings are undamaged. If the grease lines are split, grease will not reach the components that require lubricating. Machine damage will result. |
Park the machine on a level surface. Ensure that the parking brake is fully engaged. Lower the dump body and stop the engine.
If regular lubrication is carried out at the recommended intervals, only one or two shots of grease will be required at each fitting. If more than two shots of grease per fitting are required, the lines may be split or damaged, and grease will not reach the steering cylinder pins.
Remove the plastic caps and clean the fittings before you apply grease. Reinstall the plastic caps once grease has been applied.
- Install the steering frame lock. Refer to Operation and Maintenance Manual, "Steering Frame Lock".
Show/hide table
Illustration 1 g00684408 - Lubricate the front steering cylinder bearings through the fittings on the panel.
Show/hide table
Illustration 2 g00684427 - Lubricate the rear steering cylinder bearings through fittings on the cylinders.
- Remove the steering frame locks.
Caterpillar Information System:
2000/04/03 Improved Serviceability for the Grease Fitting on the Boom Raise Cylinder {5456}
CS-431C, CP-433C and CS-433C Vibratory Compactors Propel System Cab Mounting
120H Motor Grader Cooling System Coolant (ELC) - Change
10-20B Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Screed Width Control
143H and 163H Motor Graders Cooling System Coolant (ELC) - Change
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Screed Travel Lock
554 Forwarder and 574 Forwarder Steering Cylinder Mounting Bolts - Tighten
3508B Engine for 854G Wheel Dozers and 992G Wheel Loaders ECM/Personality Module
3408E and 3412E Engines for Caterpillar Built Machines Flywheel - Inspect
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Operator Monitor
3508B Engine for 854G Wheel Dozers and 992G Wheel Loaders Analog Sensor Supply
554 Forwarder and 574 Forwarder Machine System Pressures - Test/Adjust
TH103 Telehandler Safety Signs and Labels
Powering and Interfacing to Agricultural Implement Electronic Systems{1408, 6304, 6330, 6331, 7300, 7332, 7490} Powering and Interfacing to Agricultural Implement Electronic Systems{1408, 6304, 6330, 6331, 7300, 7332, 7490}
140H and 160H Motor Graders Cooling System Coolant (ELC) - Change
10-20B Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Crown Control
16H Motor Grader Cooling System Coolant (ELC) - Change
3508B Engine for 854G Wheel Dozers and 992G Wheel Loaders Engine Speed/Timing Sensor
550 Wheel Harvester, 570 Wheel Harvester and 580 Wheel Harvester Power Train Piston Pump (Power Train)
784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793C, 793D, 797 and 797B Off-Highway Trucks VIMS ™ MID 049 - CID 0890 - FMI 09
2000/05/01 Additional Clutch Disc and Plate Improve Transmission Performance {3030}
776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Oil Filter and Base (Transmission Charging) - Disassemble
776D Wheeled Tractor and 777D and 777D HAA Off-Highway Trucks Power Train Oil Filter and Base (Transmission Charging) - Assemble
784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793C, 793D, 797 and 797B Off-Highway Trucks VIMS ™ MID 049 - CID 1273 - FMI 02