Governor and Brake Control - Install
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install the governor and decelerator (12) to the original location. Install four bolts (13) .
Show/hide table
 | |
| Illustration 1 | g00659224 |
- Install plate (10) to the original location. Install two bolts (11) and the washers.
Show/hide table
 | |
| Illustration 2 | g00659222 |
- Install cover (8) and the spacer. Install four bolts (9) and the washers.
Show/hide table
 | |
| Illustration 3 | g00659221 |
- Install the rod on the bellcrank. Install nut (7) .
Show/hide table
 | |
| Illustration 4 | g00659219 |
- Connect three electrical connectors (6) .
Show/hide table
 | |
| Illustration 5 | g00659218 |
- Install cover (4) in the original location. Install three bolts (5) and the washers.
Show/hide table
 | |
| Illustration 6 | g00659217 |
- Install cover (3) to the original location. Install three bolts (2) and the washers.
Show/hide table
 | |
| Illustration 7 | g00659216 |
- Connect two electrical connectors (1) .
Show/hide table
 | |
| Illustration 8 | g00659208 |
Caterpillar Information System:
D250E and D300E Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hoist Cylinder
CB-535B Vibratory Compactor Fire Extinguisher Location
1999/12/06 The Operation of the Transmission After Applying the Parking Brake {3030, 4267}
CB-535B Vibratory Compactor Fire Prevention and Explosion Prevention
CB-535B Vibratory Compactor Burn Prevention
D250E and D300E Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Hoist Cylinder
572R Pipelayer Machine Systems Governor and Brake Control - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
CB-535B Vibratory Compactor Crushing Prevention and Cutting Prevention
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head Hydraulic System Diameter Sensor
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head Hydraulic System Length Sensor
554 and 574 Forwarders Power Train Combination Valve (Differential Lock and Parking Brake)
D250E Series II and D300E Series II Articulated Trucks Service Light Power Receptacle
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C-12, C-15 and C-16 Engines for Caterpillar Built Machines Excessive Engine Oil Consumption
572R Pipelayer Machine Systems Governor and Brake Control - Disassemble
CB-535B Vibratory Compactor Electrical Storm Injury Prevention
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
D250E Series II, D300E Series II, D350E Series II and D400E Series II Articulated Trucks Power Train Electronic Control System Check of Electronic Control Module Using Signal Generator and Counter
D250E and D300E Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Suspension Cylinder (Front)
TH62, TH63, TH82 and TH83 Telehandlers Hydraulic System Compensating System
2000/03/06 Special Instruction, REHS0606 Is Available For The Procedure To Retrofit 159-1801 Primary Fuel Filter Gp {1260, 1261}
D250E and D300E Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Suspension Cylinder (Front)
550 Wheel Harvester, 570 Wheel Harvester and 580 Wheel Harvester Hydraulic System Stump Treatment System