PRODUCT IMPROVEMENT PROGRAM FOR REPLACING EXHAUST COMBUSTION GROUPS INCLUDING EXTENSION PIPES ON CERTAIN 2007 C15 ON-HIGHWAY TRUCK ENGINES INSTALLED IN FREIGHTLINER CHASSIS
Usage:
REBE3115-03
Show/hide table
14Dec2007 |
(Revised 19Jun2008) |
U-649
A-550
TT-47
Show/hide table
Safety | PRODUCT IMPROVEMENT PROGRAM FOR REPLACING EXHAUST COMBUSTION GROUPS INCLUDING EXTENSION PIPES ON CERTAIN 2007 C15 ON-HIGHWAY TRUCK ENGINES INSTALLED IN FREIGHTLINER CHASSIS |
|
1061 | PI10648 |
Show/hide table
NOTE: | This Program must be administered as soon as possible.
When reporting the repair, use "PI10648" as the Part Number and "7751" as the Group Number, "56" as the Warranty Claim
Description Code and "T" as the SIMS Description Code.
|
Show/hide table
Show/hide table
NOTE: | This Revised Service Letter replaces the 14Dec2007 (Revised 23Jan2008) Service Letter. Changes have been made to Owner Notification Letter. |
Show/hide table
PROBLEM
Show/hide table
This Product Improvement Program is a Safety Recall in accordance with the US National Traffic and Motor Vehicle Safety Act and the Canadian Motor Vehicle Safety Act. The extension pipes attached to the Aftertreatment Regeneration Device (ARD) may develop a crack or hole and heat and flame may escape during a regeneration of the Diesel Particulate Filter, which may result in a fire hazard. It is a violation of US Federal law for a dealer to deliver a new motor vehicle or new or used engine covered by this Safety PIP until the PIP has been completed. |
AFFECTED PRODUCT
Show/hide table
Model | Identification Number |
*******Group 1******* | |
C15 | SDP00800-00801, 810, 815, 819, 854, 876, 1260-1263, 1265-1267, 1727, 1799, 1801 |
Show/hide table
*******Group 2******* | |
C15 | SDP04157, 4334, 4361, 4377, 4426, 4580, 4702, 4712, 4731, 4783, 4797, 4800, 4807, 4812, 4814, 4828, 4837-4839, 4845, 4849, 4854, 4857, 4860, 4868-4869, 4890-4891, 4893, 4901-4903, 4913, 4931, 4936, 4944, 4947, 4952, 4960, 4963, 4970, 4978, 4981-4983, 4986, 5045, 5053, 5057, 5068, 5072, 5077, 5090, 5102, 5120, 5143, 5152, 5178, 5183, 5185, 5190, 5195, 5289, 5296, 5304, 5308-5309, 5312, 5314-5315, 5317, 5328, 5338, 5340-5342, 5353-5354, 5357, 5360, 5716, 5997-5998, 6018, 6029, 6181 |
Show/hide table
*******Group 3******* | |
C15 | SDP06042, 6066, 6207, 6378, 6384, 6444, 6449, 6455, 6472, 6476, 6485, 6492, 6509, 6514, 6518, 6526-6527, 6544, 6571, 6573, 6579, 6587, 6590, 6593, 6598, 6603, 6609, 6615, 6622, 6630, 6659, 6666, 6820, 6849, 6859, 6871, 6887, 6898, 6969, 7207, 7209, 7227-7228, 7322, 7369, 7392, 7404, 7502, 7569, 7667, 7760, 7972, 8129, 8182, 8206, 8256, 8373, 8466, 8615, 8667, 8672, 8689-8690, 8707, 8713, 8716, 8724, 8731-8732, 8740, 8801, 8804, 8812, 8815, 8824, 8830, 8833-8834, 8839-8840, 8850, 8853-8855, 8871, 8875-8876, 8878-8879, 8884, 8891, 8893-8895, 8897, 8901, 8904-8905, 8908, 8914, 8916-8917, 8922, 8933, 8939, 8942, 8960, 8967, 8980, 8991, 8994, 8997, 9010, 9012, 9017, 9023, 9037, 9051, 9059, 9075, 9090, 9120, 9124, 9131, 9158, 9201, 9212, 9218, 9227, 9236, 9246-9247, 9265, 9280, 9305-9306, 9312, 9385, 9391, 9404, 9440, 9461, 9571, 9594, 9641, 9959, 10085, 10098, 10129, 10179, 10321 |
PARTS NEEDED
Show/hide table
Qty |
Part Number | Description |
*******Group 1******* | ||
4 | 3E4352 | WASHER-HARD |
2 | 5P0599 | CLAMP-BAND |
7 | 9X8267 | WASHER |
1 | 2840671 | CLAMP-V-BAND |
7 | 2840761 | BOLT-HEX HEAD |
2 | 2890728 | NUT-HEX |
2 | 2903930 | BOLT-HEX HEAD |
5 | 2914454 | SPACER |
5 | 2915204 | LOCKNUT-HEX FLG |
5 | 2934967 | STUD-TAPERLOCK |
2 | 2967780 | GASKET |
1 | 3034326 | SHIELD-HEAT (As Required) |
1 | 3034327 | SHIELD-HEAT (As Required) |
1 | 3038533 | TUBE AS.-AIR |
1 | 3041024 | SHIELD-HEAT |
1 | 3041025 | SHIELD-HEAT |
1 | 3079892 | CLAMP-V-BAND |
1 | 3109305 | EXTENSION AS. |
1 | 3110872 | BODY-MACHINED |
In Order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 40% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer. | ||
*******Group 2******* | ||
4 | 3E4352 | WASHER-HARD |
2 | 5P0599 | CLAMP-BAND |
7 | 9X8267 | WASHER |
1 | 2840671 | CLAMP-V-BAND |
7 | 2840761 | BOLT-HEX HEAD |
2 | 2890728 | NUT-HEX |
2 | 2903930 | BOLT-HEX HEAD |
5 | 2914454 | SPACER |
5 | 2915204 | LOCKNUT-HEX FLG |
5 | 2934967 | STUD-TAPERLOCK |
2 | 2967780 | GASKET |
1 | 3034326 | SHIELD-HEAT (As Required) |
1 | 3034327 | SHIELD-HEAT |
1 | 3038533 | TUBE AS.-AIR |
1 | 3041024 | SHIELD-HEAT |
1 | 3041025 | SHIELD-HEAT |
1 | 3079892 | CLAMP-V-BAND |
1 | 3109305 | EXTENSION AS. |
1 | 3110872 | BODY-MACHINED |
In Order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 40% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer. | ||
*******Group 3******* | ||
2 | 5P0599 | CLAMP-BAND |
1 | 3034326 | SHIELD-HEAT (As Required) |
1 | 3034327 | SHIELD-HEAT |
1 | 3079892 | CLAMP-V-BAND |
1 | 3109305 | EXTENSION AS. |
In Order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 40% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer. |
ACTION REQUIRED
Show/hide table
Refer to the attached Rework Procedure. |
Show/hide table
OWNER NOTIFICATION
Show/hide table
PRODUCT IMPROVEMENT PROGRAM RECALL NOTIFICATION FOR REPLACING THE AFTERTREATMENT REGENERATION DEVICE EXTENTION PIPE |
SERVICE CLAIM ALLOWANCES
Show/hide table
Show/hide table
NOTE: This is a 8.0-hour job for Group 1 | |||||
Dealer to perform most economical repair. Description___________________SMCS Code______Hours Wash__________________________107P-074_______0.3 Troubleshooting/ECM Download__107P-035_______0.6 ECM Flash_____________________1901-591_______0.5 Perform rework procedure______108B-010_______6.6 Exception may be allowed depending on chassis type. |
Show/hide table
Show/hide table
Show/hide table
NOTE: This is a 8.0-hour job for Group 2 | |||||
Dealer to perform most economical repair. Description___________________SMCS Code______Hours Wash__________________________107P-074_______0.3 Troubleshooting/ECM Download__107P-035_______0.6 ECM Flash_____________________1901-591_______0.5 Perform rework procedure______108B-010_______6.6 Exception may be allowed depending on chassis type. |
Show/hide table
Show/hide table
Show/hide table
NOTE: This is a 6.0-hour job for Group 3 | |||||
Dealer to perform most economical repair. Description___________________SMCS Code______Hours Wash__________________________107P-074_______0.3 Troubleshooting/ECM Download__107P-035_______0.6 ECM Flash_____________________1901-591_______0.5 Perform rework procedure______108B-010_______4.6 Exception may be allowed depending on chassis type. |
Show/hide table
PARTS DISPOSITION
Show/hide table
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling. |
MAKE EVERY EFFORT TO COMPLETE THIS PROGRAM AS SOON AS POSSIBLE. |
Show/hide table
IMPORTANT: SAFETY NOTICE SAFETY ? PRODUCT IMPROVEMENT PROGRAM RECALL NOTIFICATION FOR REPLACING THE AFTERTREATMENT REGENERATION DEVICE EXTENTION PIPE MODELS INVOLVED - CERTAIN MODEL YEAR 2007 C15 TRUCK ENGINES Dear Caterpillar Product Owner: This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. This notice is also in accordance with the requirements of the Canadian Motor Vehicle Safety Act. Caterpillar has decided that a defect which relates to motor vehicle safety exists in certain Freightliner trucks equipped with Caterpillar C15 truck engines. The extension pipes attached to the Aftertreatment Regeneration Device (ARD) may develop a crack or hole and heat and flame may escape during a regeneration of the Diesel Particulate Filter, which may result in a fire hazard. Caterpillar strongly recommends that you not operate the vehicle and contact your Caterpillar dealer immediately to have the extension pipe replaced for the engine serial numbers listed on the attached sheet. You will not be charged for the service performed. If you are a lessor of these vehicles, you must forward this letter to your lessee within ten days. If you have had your vehicle repaired for this condition prior to receipt of this notice and incurred any costs, you may be eligible for reimbursement. Please contact Caterpillar at this toll free number (800) 447-4986. If you no longer own the truck with this engine, please contact Caterpillar at this toll free number (800) 447-4986. Contact your local Caterpillar dealer immediately to schedule this service. The dealer will advise you of the time required to complete this service. If the dealer is unable to have the inspection and repair made, please contact: Caterpillar Inc. PO Box 610 Mossville, IL 61552-610 Attn: Engine Products Division Truck Engine Call Center Telephone: (800) 447-4986 If you are unable to have the inspection and repair made within 60 days or without charge, you may submit a complaint to: In the U.S. Administrator National Highway Traffic Safety Administration 1200 New Jersey Avenue, S.E. Washington, D.C. 20590 Telephone: 1-888-327-4236 (TTY:1-800-424-9153)or go to http://www.safercar.gov In Canada: Transport Canada Road Safety and Motor Vehicle Regulation Ottawa, Ontario KIA 0N5 Telephone: (613) 993-9851 Please refer the dealer to their Service Letter dated 14Dec2007 when scheduling this service. We regret the inconvenience this may cause you, but urge you to have this service performed for your added safety and satisfaction. Caterpillar Inc. Identification #(s) Attached to 14Dec2007 Service Letter |
Show/hide table
Group Number 1 |
1. Remove combustion body group (ARD) by referencing RENR9706 "Combustion Body Group (ARD) - Removal Procedure". 2. Remove the ARD extension pipe assembly. 3. Install 304-1024 and 304-1025 Heat Shields on the new 311-0872 ARD Body with 284-0761 Bolts and 9X-8267 Washers. Tighten to a torque of 12 +/- 1 Nm. (Image 1.1.1) |
Image1.1.1 |
4. Install combustion head group (ARD) by following steps 1-3 in media RENR9706 "Combustion Head Group (ARD) ? Installation Procedure". 5. Install combustion body group (ARD) by referencing media RENR9706 "Combustion Body Group (ARD) ? Installation Procedure". 6. Replace ARD combustion air tube assembly with replacement PN 303-8533. 7. Install 303-4326 and 303-4327 Heat Shields on the 310-9305 Extension Pipe with 2 5P-0599 Band Clamps and tighten to a torque of 4 Nm +/- 1 Nm. |
Image1.2.1 |
8. Assemble the flared end of extension pipe assembly to the combustion group body with new 307-9892 V-band Clamp. Do not tighten clamp at this time. 9. Align extension pipe with chassis exhaust pipe. Do not tighten OEM supplied v-band clamp at this time. 10. Inspect for interferences with chassis or other components and align piping as necessary. 11. Tighten the 307-9892 V-band Clamp that connects the extension pipe to the combustion body to a torque of 12 +/- 1 Nm. 12. Tighten the OEM supplied v-band clamp that connects the extension pipe to the chassis exhaust according to OEM specifications using a new clamp. 13. Flash Engine Electronic Control Module with the latest software according to SIS web. If SIS web is not available then contact the Truck Engine Call Center. (1-800-477-4986) 14. Perform ARD ignition test in CAT ET. |
Group Number 2 |
1. Remove combustion body group (ARD) by referencing RENR9706 "Combustion Body Group (ARD) - Removal Procedure". 2. Remove the ARD extension pipe assembly. 3. Install 304-1024 and 304-1025 Heat Shields on the new 311-0872 ARD Body with 284-0761 Bolts and 9X-8267 Washers. Tighten to a torque of 12 +/- 1 Nm. |
Image2.1.1 |
4. Install combustion head group (ARD) by following steps 1-3 in media RENR9706 "Combustion Head Group (ARD) ? Installation Procedure". 5. Install combustion body group (ARD) by referencing media RENR9706 "Combustion Body Group (ARD) ? Installation Procedure". 6. Replace ARD combustion air tube assembly with replacement PN 303-8533. 7. Replace the extension pipe with a new 310-9305 Extension Pipe. NOTE: The 303-4326 and 303-4327 Heat Shields are to be replaced with new parts. NOTE: All in stock replacement pipes have been inspected and are verified for installation. |
8. Re-install 303-4326 and 303-4327 Heat Shields on the 310-9305 Extension Pipe with 2 5P-0599 Band Clamps and tighten to a torque of 4 Nm +/- 1 Nm. |
Image2.3.1 |
9. Assemble flared end of extension pipe assembly to the combustion group body with new 307-9892 V-band Clamp. Do not tighten clamp at this time. 10. Align extension pipe with chassis exhaust pipe. Do not tighten OEM supplied v-band clamp at this time. 11. Inspect for interferences with chassis or other components and align piping as necessary. 12. Tighten the 307-9892 V-band Clamp that connects the extension pipe to the combustion body to a torque of 12 +/- 1 Nm. 13. Tighten the OEM supplied v-band clamp that connects the extension pipe to the chassis exhaust according to OEM specifications using a new clamp. 14. Flash Engine Electronic Control Module with the latest software according to SIS web. If SIS web is not available then contact the Truck Engine Call Center. (1-800-477-4986) 15. Perform ARD ignition test in CAT ET. |
Group Number 3 |
1. Remove the ARD extension pipe assembly. NOTE: The 303-4326 and 303-4327 Heat Shields are to be replaced with new parts. NOTE: All in stock replacement pipes have been inspected and are verified for installation. |
2. Install 303-4326 and 303-4327 Heat Shields on the 310-9305 Extension Pipe with 2 5P-0599 Band Clamps and tighten to a torque of 4 Nm +/- 1 Nm. |
Image3.2.1 |
3. Assemble the flared end of extension pipe assembly to the combustion group body with new 307-9892 V-band Clamp. Do not tighten clamp at this time. 4. Align extension pipe with chassis exhaust pipe. Do not tighten OEM supplied v-band clamp at this time. 5. Inspect for interferences with chassis or other components and align piping as necessary. 6. Tighten the 307-9892 V-band Clamp that connects the extension pipe to the combustion body to a torque of 12 +/- 1 Nm. 7. Tighten the OEM supplied v-band clamp that connects the extension pipe to the chassis exhaust according to OEM specifications using a new clamp. 8. Flash Engine Electronic Control Module with the latest software according to SIS web. If SIS web is not available then contact the Truck Engine Call Center. (1-800-477-4986) 9. Perform ARD ignition test in CAT ET. |
Caterpillar Information System:
PRODUCT SUPPORT PROGRAM FOR REPLACING THE INLET ELBOW FOR THE FUEL TRANSFER PUMP ON CERTAIN C13 2007 INTERNATIONAL TRUCK ENGINES PRODUCT SUPPORT PROGRAM FOR REPLACING THE INLET ELBOW FOR THE FUEL TRANSFER PUMP ON CERTAIN C13 2007 INTERNATIONAL TRUCK ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE BREAKER CONNECTOR MOUNTING BOLTS AND INTERFACE WIRING CABLES ON CERTAIN 3516B AND 3516C PACKAGE GENERATOR SETS WITH 4000 AMP BREAKERS PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE BREAKER CONNECTOR MOUNTING BOLTS AND INTERFACE WIRING CABLES ON CERTAIN 3516B AND 3516C PACKAGE GENERATOR SETS WITH 4000 AMP BREAKERS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE VIBRATION DAMPER AND INSTALLING THE NEW SPACER AND BOLTS ON CERTAIN 3126B, C7, AND C9 MARINE ENGINES PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE VIBRATION DAMPER AND INSTALLING THE NEW SPACER AND BOLTS ON CERTAIN 3126B, C7, AND C9 MARINE ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND REPLACING THE ALTERNATOR/START RELAY CIRCUIT BREAKER, START RELAY, AND INLET AIR HEATER CIRCUIT BREAKER ON CERTAIN C7 AND C9 MARINE ENGINES PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING AND REPLACING THE ALTERNATOR/START RELAY CIRCUIT BREAKER, START RELAY, AND INLET AIR HEATER CIRCUIT BREAKER ON CERTAIN C7 AND C9 MARINE ENGINES
PRODUCT SUPPORT PROGRAM FOR REDUCTION OF AFTERCOOLER CONDENSATE ON CERTAIN C12/3196 MARINE ENGINES PRODUCT SUPPORT PROGRAM FOR REDUCTION OF AFTERCOOLER CONDENSATE ON CERTAIN C12/3196 MARINE ENGINES
PRODUCT SUPPORT PROGRAM FOR REPLACING PLC SOFTWARE ON CERTAIN ISO SWITCHGEAR (CAT POWER MODULES 297-6974, 298-2714, AND 300-7399) PRODUCT SUPPORT PROGRAM FOR REPLACING PLC SOFTWARE ON CERTAIN ISO SWITCHGEAR (CAT POWER MODULES 297-6974, 298-2714, AND 300-7399)
PRODUCT SUPPORT PROGRAM FOR THE REPLACEMENT OF THE LOW PRESSURE ACTUATORS (LPA) FOR THE INTAKE VALVE ON CERTAIN C13 TRUCK ENGINES PRODUCT SUPPORT PROGRAM FOR THE REPLACEMENT OF THE LOW PRESSURE ACTUATORS (LPA) FOR THE INTAKE VALVE ON CERTAIN C13 TRUCK ENGINES
PRODUCT SUPPORT PROGRAM FOR REPLACING TOUCHSCREEN PROCESSORS ON CERTAIN ISO SWITCHGEAR PRODUCT SUPPORT PROGRAM FOR REPLACING TOUCHSCREEN PROCESSORS ON CERTAIN ISO SWITCHGEAR
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE GENERATOR ON CERTAIN 3456 AND C15 60HZ GENERATOR SETS PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE GENERATOR ON CERTAIN 3456 AND C15 60HZ GENERATOR SETS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE ENGINE EMISSIONS STICKER ON CERTAIN C13 AND C15 ON-HIGHWAY ENGINES PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE ENGINE EMISSIONS STICKER ON CERTAIN C13 AND C15 ON-HIGHWAY ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AFTERTREATMENT REGENERATION DEVICE FUEL LINE PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE AFTERTREATMENT REGENERATION DEVICE FUEL LINE
PRODUCT SUPPORT PROGRAM FOR REORIENTING THE JACKET WATER HEATER ON CERTAIN C15 AND C18 ENGINES PRODUCT SUPPORT PROGRAM FOR REORIENTING THE JACKET WATER HEATER ON CERTAIN C15 AND C18 ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR SAFETY RECALL ON CERTAIN 2007 C15 ON-HIGHWAY TRUCK ENGINES INSTALLED IN FREIGHTLINER CHASSIS PRODUCT IMPROVEMENT PROGRAM FOR SAFETY RECALL ON CERTAIN 2007 C15 ON-HIGHWAY TRUCK ENGINES INSTALLED IN FREIGHTLINER CHASSIS
PRODUCT IMPROVEMENT PROGRAM FOR REPROGRAMMING CUSTOMER COMMUNICATION MODULE 164-8940 FOR COMPATIBILITY WITH CERTAIN 3508B LOCOMOTIVE ENGINES WITH AN ADEM III CONTROL PRODUCT IMPROVEMENT PROGRAM FOR REPROGRAMMING CUSTOMER COMMUNICATION MODULE 164-8940 FOR COMPATIBILITY WITH CERTAIN 3508B LOCOMOTIVE ENGINES WITH AN ADEM III CONTROL
PRODUCT SUPPORT PROGRAM FOR REPLACING EXHAUST COMBUSTION GROUPS ON CERTAIN 2007 C15 ON-HIGHWAY TRUCK ENGINES INSTALLED IN SISU CHASSIS PRODUCT SUPPORT PROGRAM FOR REPLACING EXHAUST COMBUSTION GROUPS ON CERTAIN 2007 C15 ON-HIGHWAY TRUCK ENGINES INSTALLED IN SISU CHASSIS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE 243-3817 SEAWATER TUBE ON CERTAIN C12 COMPACT MARINE ENGINES PRODUCT SUPPORT PROGRAM FOR REPLACING THE 243-3817 SEAWATER TUBE ON CERTAIN C12 COMPACT MARINE ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE TURBOCHARGER ON CERTAIN C6.6 ENGINES PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE TURBOCHARGER ON CERTAIN C6.6 ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE FUEL FILTER ON CERTAIN 3508B MARINE GENSETS AND 3516B MARINE PROPULSION ENGINES PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE FUEL FILTER ON CERTAIN 3508B MARINE GENSETS AND 3516B MARINE PROPULSION ENGINES
PRODUCT SUPPORT PROGRAM FOR REPLACING THE WATER PUMP ON CERTAIN C6.6 ENGINES PRODUCT SUPPORT PROGRAM FOR REPLACING THE WATER PUMP ON CERTAIN C6.6 ENGINES
PRODUCT SUPPORT PROGRAM FOR REWORKING 289-3607 FLEXPLATES ON CERTAIN C10 INDUSTRIAL ENGINES PRODUCT SUPPORT PROGRAM FOR REWORKING 289-3607 FLEXPLATES ON CERTAIN C10 INDUSTRIAL ENGINES
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE 5N-3765 GENERATOR SET COUPLING WITH A 247-0308 COUPLING ON CERTAIN G3520C GENERATOR SETS PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE 5N-3765 GENERATOR SET COUPLING WITH A 247-0308 COUPLING ON CERTAIN G3520C GENERATOR SETS
PRODUCT SUPPORT PROGRAM FOR INSTALLING THE ENGINE CONTROL SOFTWARE ON CERTAIN C9 ON-HIGHWAY TRUCK ENGINES INSTALLED IN BUS CHASSIS PRODUCT SUPPORT PROGRAM FOR INSTALLING THE ENGINE CONTROL SOFTWARE ON CERTAIN C9 ON-HIGHWAY TRUCK ENGINES INSTALLED IN BUS CHASSIS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE ENGINE ELECTRONIC CONTROL MODULE (ECM) SOFTWARE AND POSSIBLY THE INJECTORS ON CERTAIN C18 INDUSTRIAL ENGINES PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE ENGINE ELECTRONIC CONTROL MODULE (ECM) SOFTWARE AND POSSIBLY THE INJECTORS ON CERTAIN C18 INDUSTRIAL ENGINES
PRODUCT SUPPORT PROGRAM FOR REWORKING OIL FILL TUBES ON CERTAIN 2007 C13 AND C15 ON-HIGHWAY TRUCK ENGINES PRODUCT SUPPORT PROGRAM FOR REWORKING OIL FILL TUBES ON CERTAIN 2007 C13 AND C15 ON-HIGHWAY TRUCK ENGINES