Hoist Cylinder - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 1/2 in - 13 X 9.5 in 螺杆 | 3 | |
B | 5P-0599 | 软管夹 | 1 |
C | 1F-7958 | 1/2 in - 13 NC 螺母 | 3 |
D | 8S-9906 | 棘轮拉拔器 | 1 |
E | 4C-5591 | 防粘结剂 | 1 |
- 检查所有 O 形密封圈和部件有无磨损或损坏。 如有必要,请更换部件。
- 利用所密封的润滑剂轻轻润滑所有 O 形密封圈。
注: 以下程序对于机器两侧完全相同。 必要时,对机器的另一侧重复此程序。
Show/hide table图 1 g00546971 - 将挡圈安装至机架组件。 如图所示,将工具 (A) 安装至挡圈。
- 将外座圈 (8) 安装至机架组件。 如图所示,将工具 (B) 置于外座圈 (8) 周围,以安装举倾机构油缸。
Show/hide table
图 2 g00547005 - 如图所示,将举倾机构油缸 (2) 的连杆端置于机器上。 举倾机构油缸 (2) 的重量约为
285 kg (630 lb) 。 将举倾机构油缸 (2) 滑过外座圈 (8)。 - 从外座圈 (8) 上拆下软管卡箍。 如图所示,将工具 (C) 安装在工具 (A) 上。 使用工具 (C) 使举倾机构油缸 (2) 座落至机架组件。 将举倾机构油缸 (2) 降低至后轮上。
Show/hide table
图 3 g00546897 - 拆下工具 (A)(图中未显示)和工具 (C)(图中未显示)。 将盖 (7) 和螺栓 (6) 安装到举倾机构油缸 (2) 上。
Show/hide table
图 4 g00613412 - 将工具 (D) 安装至举倾机构油缸 (2) 的盖端,然后将举倾机构 (2) 置于车身上。
Show/hide table
图 5 g00546861 - 将工具 (E) 涂敷到销组件 (5)。 将销组件 (5) 安装至举倾机构油缸 (2) 的盖端。
- 将板 (4)、螺栓 (3) 和硬垫圈安装至举倾机构油缸 (2)。
Show/hide table
图 6 g00546840 - 将软管组件 (1) 连接至举倾机构油缸 (2)。
- 重新加注液压油箱(举倾机构和制动器)。 请参阅操作和保养手册, "举倾机构和制动器油箱油 - 更换"。 液压油箱(举倾机构和制动器)的容量为
133 L (35 US gal) 。
结束:
- 取走车轮楔子。 请参阅拆解和组装, "车轮楔子(前和后)- 拆卸和安装"。
Caterpillar Information System:
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Piston Pump (Steering) - Install
416C, 426C, 428C, 436C and 438C Backhoe Loaders Axles, Differential and Brakes Axle (Front)
3054 and 3056 Industrial and Generator Set Engines Front Cover - Remove and Install
3054 Engine for Caterpillar Built Machines Flywheel - Install
583R Pipelayer Machine Systems Hook Cable Guide Sheave - Remove
3054 Engine for Caterpillar Built Machines Flywheel - Remove
3054 Engine for Caterpillar Built Machines Camshaft - Remove and Install
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Hoist Cylinder - Remove
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Piston Pump (Steering) - Remove
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Hydraulic Filter (Parking Brake Release) - Remove and Install
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Metering Pump (HMU)
3512B and 3516B Engine Supplement for and 784C,, 785C and and 785C HAA Off-Highway Truck/Tractors Muffler - Remove
583R Pipelayer Machine Systems Boom Kickout Mechanism - Remove
3054 Engine for Caterpillar Built Machines Front Cover - Install
3054 Engine for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
583R Pipelayer Machine Systems Boom Kickout Mechanism - Install
834G Wheel Dozer and 836G Landfill Compactor Electrohydraulic System Relief Valve (Main)
3406E Truck Engine Housing (Front)
CB-434C, CB-534C and CB-634C Vibratory Compactors Water Spray System Water Strainer
3408E and 3412E Engines for Caterpillar Built Machines Coolant Temperature Sensor - Remove and Install
3054 Engine for Caterpillar Built Machines Engine Oil Pan - Remove and Install
3516B Engine Supplement for 793C Off-Highway Truck Belt Tightener - Install
3408E and 3412E Engines for Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Relay Valve (Brake) - Install