Hydraulic Tank (Torque Converter, Pulled Unit, Brake, and Transmission)
Show/hide table
 | |
| Illustration 1 | g00480051 |
Show/hide table
 | |
| Illustration 2 | g00289473 |
Section A-A | |
(1) Torque for 73 bolts ... 50 ± 7 N·m (37 ± 5 lb ft)
(2) Torque for 45 bolts ... 50 ± 7 N·m (37 ± 5 lb ft)
(3) Torque for 10 bolts ... 50 ± 7 N·m (37 ± 5 lb ft)
(4) Torque for 14 bolts ... 30 ± 5 N·m (22 ± 4 lb ft)
(7) 7B-3039 Spring
- Length under test force ... 26.2 mm (1.03 inch)
- Test force ... 15.6 ± 1.2 N (3.51 ± 0.270 lb)
- Free length after test ... 36.6 mm (1.44 inch)
- Outside diameter ... 16.66 mm (0.656 inch)
- Test force ... 15.6 ± 1.2 N (3.51 ± 0.270 lb)
(8) Torque for two plugs ... 68 ± 7 N·m (50 ± 5 lb ft)
Caterpillar Information System:
550, 570 and 580 Wheel Harvesters Parking Brake Manual Release
784C, 785C and 785C HAA Off-Highway Truck/Tractors Hydraulic System Hydraulic Tank (Torque Converter, Hoist, Brake and Transmission)
3408E and 3412E Engines for Caterpillar Built Machines Coolant Temperature Sensor
3304B and 3306B Engines for Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
C-10 and C-12 Industrial Engines Fuel Temperature Sensor
3408E and 3412E Engines for Caterpillar Built Machines Inlet Air Temperature Sensor
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Pilot Operated Hydraulic Control - Assemble
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Pilot Operated Hydraulic Control - Disassemble
966G Wheel Loader and 972G Wheel Loader Power Train Sensors
Procedure for Reworking the Pin Bores for Swing Cylinders on the Swing Frame{5105} Procedure for Reworking the Pin Bores for Swing Cylinders on the Swing Frame{5105}
Electronic Modular Control Panel II (EMCP II) For MUI Engines Connector Contact Identification of Generator Set Control
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Three-Point Hitch Lift Cylinder
793C Off-Highway Truck Machine Systems Hydraulic Tank - Assemble
550, 570 and 580 Wheel Harvesters Swing Brake Manual Release
784C and 785C Off-Highway Trucks Machine Systems Steering Tank and Filter - Remove
793C Off-Highway Truck Machine Systems Gear Pump (Hoist) - Remove
24H Motor Grader Hydraulic and Steering System Pressure Switch (Steering)
793C Off-Highway Truck Machine Systems Gear Pump (Hoist) - Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0444 FMI 03 Magnetic Switch (Start Relay) Voltage Above Normal - Test
3406C Engines for Caterpillar Built Machines Fuel Injection Lines
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Bank Valve - Install
24H Motor Grader Hydraulic and Steering System Temperature Switch (Hydraulic Oil)
3406E On-Highway Engine Electric Starting Motor - Remove and Install
966G Wheel Loader and 972G Wheel Loader Power Train Switches