Engine Oil Filter and Oil Filter Base - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 2P-8250     | Strap Wrench     | 1     |
Show/hide table
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose of all fluids according to local regulations and mandates. |
- Open the engine hood.
- Drain the coolant from the radiator. The capacity of the coolant system is 63 L (17 US gal) .
- Use Tooling (A) in order to remove oil filter (3) from oil filter base (2) . Disconnect oil hose (1) from oil filter base (2) .
Show/hide table
Illustration 1 | g00479895 |
- Remove two bolts (6) that secure pipe (5) to the engine.
Show/hide table
Illustration 2 | g00479944 |
- Remove pipe (5) and the O-ring seals from fuel filter base (2) and the engine.
- Remove bolt (8) that secures pipe clamp (7) . Clamp (7) secures pipe (4) to the engine. Remove spacer (9) that is under pipe clamp (7) and under bolt (8) .
- Remove two bolts (10) from pipe (4) . Remove pipe (4) from the engine and from the oil filter base. Gasket (11) will separate with pipe (4) .
Show/hide table
Illustration 3 | g00479948 |
- Remove gasket (11) from the lower end of pipe (4) and remove O-ring (12) from the upper end of pipe (4) .
Show/hide table
Illustration 4 | g00479955 |
- Remove O-ring seals (13) and (14) from pipe (5) .
Show/hide table
Illustration 5 | g00479950 |
- Remove four bolts (15) and remove oil filter base (2) from the engine.
Show/hide table
Illustration 6 | g00479957 |
- Remove two O-ring seals (16) from oil filter base (2) .
Show/hide table
Illustration 7 | g00479980 |
- Turn over the oil filter base and remove hollow stud (17) from oil filter base (2) .
Show/hide table
Illustration 8 | g00479982 |
- Turn over the oil filter base and remove four bolts (19) and cover (18) from oil filter base (2) .
Show/hide table
Illustration 9 | g00479987 |
- Remove cap (20) and test port (21) from oil filter base (2) . Remove the O-ring seal from test port (21) .
- Remove two springs (23) from oil filter base (2) . Both springs are identical.
Show/hide table
Illustration 10 | g00479993 |
- Remove gasket (22) from oil filter base (2) .
- Remove two plungers (24) from oil filter base (2) . Both plungers are identical.
Show/hide table
Illustration 11 | g00479999 |
Installation Procedure
- Inspect all parts and clean all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
- Install two plungers (24) to oil filter base (2) . Both plungers are identical.
Show/hide table
Illustration 12 | g00479999 |
- Install gasket (22) to oil filter base (2) .
Show/hide table
Illustration 13 | g00479993 |
- Install two springs (23) to oil filter base (2) . Both springs are identical.
- Install the O-ring seal to test port (21) . Install cap (20) and test port (21) to oil filter base (2) .
Show/hide table
Illustration 14 | g00479987 |
- Install four bolts (19) and cover (18) to oil filter base (2) .
- Install hollow stud (17) to oil filter base (2) .
Show/hide table
Illustration 15 | g00479982 |
- Install two O-ring seals (16) to oil filter base (2) .
Show/hide table
Illustration 16 | g00479980 |
- Position oil filter base (2) to the engine. Install four bolts (15) .
Show/hide table
Illustration 17 | g00479957 |
- Install gasket (11) to the lower end of pipe (4) and install O-ring (12) to the upper end of pipe (4) .
Show/hide table
Illustration 18 | g00479955 |
- Install O-ring seals (13) and (14) to pipe (5) .
Show/hide table
Illustration 19 | g00479950 |
- Position pipe (4) to the engine and to the oil filter base. Gasket (11) will be installed with pipe (4) . Install two bolts (10) to pipe (4) .
Show/hide table
Illustration 20 | g00479948 |
- Install spacer (9) under pipe clamp (7) and under bolt (8) . Install bolt (8) that secures pipe clamp (7) and pipe (4) to the engine.
Show/hide table
Illustration 21 | g00479944 |
- Install pipe (5) and the O-ring seals to fuel filter base (2) and the engine.
- Install two bolts (6) that secure pipe (5) to the engine.
- Connect oil hose (1) to oil filter base (2) . Install oil filter (3) to oil filter base (2) . Check the oil level in the engine. If necessary, add oil. Refer to Operation and Maintenance Manual, SEBU7028 for the installation procedure and the service intervals.
Show/hide table
Illustration 22 | g00479895 |
- Fill the radiator with coolant. Refer to Operation and Maintenance Manual, SEBU7028 for the proper procedure.
- Close the engine hood.
Caterpillar Information System:
980G Wheel Loader Braking System Foot Brake Control - Check and Adjust
69D and 769D Off-Highway Trucks and 771D Quarry Truck Exhaust Manifold - Install
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Hydraulic Tank - Remove
572R Pipelayer Hydraulic System Counterweight Control Valve
69D and 769D Off-Highway Trucks and 771D Quarry Truck Exhaust Manifold - Remove
35, 45 and 55 Agricultural Tractors Drive Wheel
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Bucket Linkage and Loader Cylinder Bearings - Lubricate
69D and 769D Off-Highway Trucks and 771D Quarry Truck Engine Oil Filter Bypass Valve - Remove and Install
550, 570 and 580 Wheel Harvesters Stick - Install
35, 45 and 55 Agricultural Tractors Midroller
35, 45 and 55 Agricultural Tractors Midroller
69D and 769D Off-Highway Trucks and 771D Quarry Truck Electric Drive Pump (Prelubrication) - Install
572R Pipelayer Hydraulic System Counterweight Group
69D and 769D Off-Highway Trucks and 771D Quarry Truck Turbocharger - Install
69D and 769D Off-Highway Trucks and 771D Quarry Truck Cooling System Pressure Relief Valve - Remove and Install
69D and 769D Off-Highway Trucks and 771D Quarry Truck Electronic Control Module (Engine) - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines Indicator for Engine Overspeed - Troubleshoot
572R Pipelayer Hydraulic System Pipelayer Frame Group
AP-1055B and BG-2455C Asphalt Pavers Screed Hoist Control
572R Pipelayer Hydraulic System Boom
69D and 769D Off-Highway Trucks and 771D Quarry Truck Engine Oil Cooler - Install
572R Pipelayer Hydraulic System Combination Valves
3306C Engines for Caterpillar Built Machines Ether Starting Aid
69D and 769D Off-Highway Trucks and 771D Quarry Truck Oil Cooler (Hoist and Rear Brake) - Remove