Piston Pump (Steering) - Remove
Removal Procedure
Start By:
- Remove the implement pump. Refer to Disassembly and Assembly, "Vane Pump (Implement, Pilot and Braking) - Remove".
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
Note: Put identification marks on all hoses and on all tubes for installation purposes. Plug all hoses and all tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
- Disconnect inlet elbow (1) .
Show/hide table
 | |
| Illustration 1 | g00353517 |
- Disconnect two hose assemblies (2) .
Show/hide table
 | |
| Illustration 2 | g00353518 |
- Disconnect hose assembly (3) .
- Attach a suitable hoist and a suitable lifting sling to piston pump (5). Remove bolts (4) .
Show/hide table
 | |
| Illustration 3 | g00353519 |
- Use the hoist in order to remove piston pump (5). The weight of the piston pump is 50 kg (110 lb).
Caterpillar Information System:
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Pump Control Valve (Steering) - Remove and Install
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Vane Pump (Implement, Pilot and Braking) - Install
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Vane Pump (Implement, Pilot and Braking) - Remove
527 Track-Type Skidder Brakes, Indicators, Gauges and Horn - Test
572R Pipelayer Track Idler
527 Track-Type Skidder Fuel Tank Water and Sediment - Drain
784B and 785B Off-Highway Truck/Tractors Engine Oil Level - Check
CP-563D, CS-563D, CS-573D and CS-583D Paving Compactors Roading the Machine
572R Pipelayer Undercarriage
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Flow Switch
550, 570 and 580 Wheel Harvesters Pendulum Arm Cylinder Bearings - Lubricate
CP-563C and CS-563C Vibratory Compactors Shipping the Machine
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Piston Pump (Steering) - Install
966G Wheel Loader and 972G Wheel Loader Power Train CID 0622 FMI 03 Push Button Switch (Upshift) Voltage Above Normal - Test
966G Wheel Loader and 972G Wheel Loader Power Train CID 0623 FMI 03 Rocker Switch (Transmission Direction) Voltage Above Normal - Test
966G Wheel Loader and 972G Wheel Loader Power Train CID 0623 FMI 04 Rocker Switch (Transmission Direction) Voltage Below Normal - Test
966G Wheel Loader and 972G Wheel Loader Power Train CID 0631 FMI 07 Modulating Valve (Clutch 1 Solenoid) Improper Mechanical Response - Test
966G Wheel Loader and 972G Wheel Loader Power Train CID 0631 FMI 13 Modulating Valve (Clutch 1 Solenoid) Out of Calibration - Test
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Transmission Control
966G Wheel Loader and 972G Wheel Loader Power Train CID 0632 FMI 03 Modulating Valve (Clutch 2 Solenoid) Voltage Above Normal - Test
966G Wheel Loader and 972G Wheel Loader Power Train CID 0632 FMI 05 Modulating Valve (Clutch 2 Solenoid) Current Below Normal - Test
966G Wheel Loader and 972G Wheel Loader Power Train CID 0632 FMI 06 Modulating Valve (Clutch 2 Solenoid) Current Above Normal - Test
966G Wheel Loader and 972G Wheel Loader Power Train CID 0632 FMI 07 Modulating Valve (Clutch 2 Solenoid) Improper Mechanical Response - Test
D250E Series II and D300E Series II Articulated Trucks 3306B Engine Supplement Water Temperature Regulator - Remove and Install