Frame - Clean/Inspect
Show/hide table
When it is necessary to work under the machine with the body (bed) raised, attach the body (bed) retaining cable to the rear tow point. Install the rear tow point pin through the end of the retaining cable. Failure to properly secure the body (bed) may result in personal injury or death. |
Show/hide table
Do not move the hoist control to the LOWER position when the body retaining cable is installed between the dump body and the rear tow pin. When the hoist control is in the LOWER position, hydraulic force may cause the body retaining cable to fail with the potential for injury or death. |
Show/hide table
Illustration 1 | g00341472 |
Show/hide table
Illustration 2 | g00287354 |
Retaining Cable |
A complete inspection of the truck frame should occur at every 500 hours.
- Raise the body until the rear tow point pin aligns with the retaining cable end from the body. Install the rear tow point pin.
- Clean the frame with a high pressure washer.
- Inspect the frame for damage and for cracks. If you find cracks or damage, consult your Caterpillar dealer for specific repair procedures. Do not operate the machine until the necessary repairs have been made.
Show/hide table
Illustration 3 | g00321325 |
Caterpillar Information System:
784B and 785B Off-Highway Truck/Tractors Ether Starting Aid Cylinder - Replace
784B and 785B Off-Highway Truck/Tractors Window Wiper - Inspect/Replace
784B and 785B Off-Highway Truck/Tractors Window - Clean
966G Wheel Loader and 972G Wheel Loader Power Train CID 0562 FMI 09 Caterpillar Monitoring System Abnormal Update - Test
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Main Control Valve - Assemble
966G Wheel Loader and 972G Wheel Loader Power Train CID 0444 FMI 06 Magnetic Switch (Start Relay) Current Above Normal - Test
784B and 785B Off-Highway Truck/Tractors Leaving the Machine
527 Track-Type Skidder Winching
789B Off-Highway Truck Hydraulic System Brake Oil Overheating Troubleshooting
966G Wheel Loader and 972G Wheel Loader Power Train CID 0444 FMI 05 Magnetic Switch (Start Relay) Current Below Normal - Test
789B Off-Highway Truck Hydraulic System Hoist, Torque Converter, and Brake System Troubleshooting
789B Off-Highway Truck Air System and Brakes General Information
784B and 785B Off-Highway Truck/Tractors Frame and Body - Inspect
784B and 785B Off-Highway Truck/Tractors Frame and Body Support Pads - Clean/Inspect
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Master Cylinder
966G Wheel Loader and 972G Wheel Loader Power Train CID 0585 FMI 02 Speed Sensor (No. 1) (Transmission Output) Incorrect Signal - Test
784B and 785B Off-Highway Truck/Tractors Air Tank Moisture and Sediment - Drain
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Power Train CID 0617 FMI 03 Magnetic Switch (Air Inlet Heater Relay) Voltage Above Normal - Test
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Power Train CID 0617 FMI 05 Magnetic Switch (Air Inlet Heater Relay) Current Below Normal - Test
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Power Train CID 0617 FMI 06 Magnetic Switch (Air Inlet Heater Relay) Current Above Normal - Test
784B and 785B Off-Highway Truck/Tractors Air Dryer - Check
966G Wheel Loader and 972G Wheel Loader Power Train CID 0621 FMI 03 Push Button Switch (Downshift) Voltage Above Normal - Test
793B Off-Highway Truck Fuel System Primary Filter - Clean
CP-563C and CS-563C Vibratory Compactors Gauges