Operation Of 119-1733 And 134-1346 12-Volt Converters Caterpillar

Operation Of 119-1733 And 134-1346 12-Volt Converters

Usage:

GENERALALL 24 VOLT MACHINES EQUIPPED WITH 12 VOLT RADIOS

Problem:

Some 12-volt converters have been erroneously replaced. The specific complaint has been that the output voltage from the converter is too high (24 volts to 28 volts) when the radio is not connected to the converter and the keyswitch is turned to the "ON" position.

Solution:

The output voltage from the converter should only be checked under the following conditions: the radio is connected to the converter, the keyswitch is turned to the "ON" position, and the radio is turned "ON". When there is no electrical load connected to the converter, it is normal for the converter output voltage to measure between 11 volts and 28 volts. When the radio is turned on, the output voltage from the converter should measure between 11 volts and 14.5 volts.

COPYRIGHT 2000 CATERPILLAR ALL RIGHTS RESERVED

Caterpillar Information System:

Metallic Noise From The 3W-5071 Parking Brake GP Metallic Noise From The 3W-5071 Parking Brake GP

Transmission Valve Bodies/Manifolds May Not Be Flat Transmission Valve Bodies/Manifolds May Not Be Flat

The 8W-4264 Mufler Brace No Longer Required The 8W-4264 Mufler Brace No Longer Required

Elevated Copper And Iron Levels Found While Performing SOS Samples On Transmissions Elevated Copper And Iron Levels Found While Performing SOS Samples On Transmissions

Right-Hand Engine Side Guard Removal Right-Hand Engine Side Guard Removal

137-9822 Sonic Sensor Field Test 137-9822 Sonic Sensor Field Test

FEEDER SYSTEM DIAGNOSIS ON ASPHALT PAVERS FEEDER SYSTEM DIAGNOSIS ON ASPHALT PAVERS

Rubber Chunking From Drive Wheel Assemblies Rubber Chunking From Drive Wheel Assemblies

Mechanical Failures Of Cat ID Mechanical Failures Of Cat ID

Service Meter Hour Limitation On Service Letter, PI3335 Service Meter Hour Limitation On Service Letter, PI3335

New Adjustment Procedure When Installing The New 170-9002 Front Suspension Ball Joints In The PF/PS-300B Pneumatic Compactors New Adjustment Procedure When Installing The New 170-9002 Front Suspension Ball Joints In The PF/PS-300B Pneumatic Compactors

155-6581 Fuel Level Sender May Malfunction 155-6581 Fuel Level Sender May Malfunction

Muffler Drain Hole Muffler Drain Hole

Wear Of The 8E-8164 Thrust Disc May Cause Transmission Wear Of The 8E-8164 Thrust Disc May Cause Transmission

Change To The Ride Control Accumulator Diameter Change To The Ride Control Accumulator Diameter

Restriction Port Indicator May Not Function Restriction Port Indicator May Not Function

Threshing Cylinder Dual Range Drive Requires The Correct Viscosity Oil Fill Threshing Cylinder Dual Range Drive Requires The Correct Viscosity Oil Fill

Correct Reel Control Module May Not Have Been Installed Correct Reel Control Module May Not Have Been Installed

Foot Brake Control Pedal Assembly Foot Brake Control Pedal Assembly

Striker Bar Failures On The 836 Landfill Compactor Striker Bar Failures On The 836 Landfill Compactor

VIMSpc99 Version 1.1.7 Is Unable To Open Some Archived Database Files VIMSpc99 Version 1.1.7 Is Unable To Open Some Archived Database Files

Air In The Brake System Air In The Brake System

Correct Installation Of 173-5734 Roller From 173-5740 Parking Brake Kit Correct Installation Of 173-5734 Roller From 173-5740 Parking Brake Kit

PC Monitor May Display "Comms Error" during field calibration of a Type II Longitudinal Stability Indicator using 145-5809 Indicator Cable Assembly PC Monitor May Display "Comms Error" during field calibration of a Type II Longitudinal Stability Indicator using 145-5809 Indicator Cable Assembly