Usage:
NOTE: This Program can be administered either before or after failure.In either case the decision whether to apply the Program is made by the dealer. When reporting the repair, use "PS40096" as the Part number and "7755" as the Group Number. If adminstered before failure, use "56" as the Warranty Claim Description Code and use "T" as the SIMS Description Code. If adminstered after failure, use "96" as the Warranty Claim Description Code and use "Z" as the SIMS Description Code.
Termination Date
December 31, 2000Problem
The front housing may crack on certain 3406E Industrial Engines.
Affected Product
Model & Identification Number
3406E (6BR973-974, 6BR988, 6BR1079-1083, 6BR1095-1100, 6BR1104-1108, 6BR1115-1120, 6BR1135-1139, 6BR1144-1148, 6BR1150-1155, 6BR1187-1190, 6BR1210-1211, 6BR1213-1215, 6BR1219-1223, 6BR1283-1292, 6BR1318-1327, 6BR1368-1372, 6BR1375-1379, 6BR1440-1447)
Parts Needed
- 2 - 3E4353 WASHER-HARD
- 1 - 2N1287 ELBOW-FLARED
- 1 - 0S1571 BOLT
- 2 - 5S0003 NUT-FULL
- 2 - 0T0573 BOLT
- 4 - 9X6458 WASHER-HARD
- 1 - 1283854 HOUSING AS (Only If Needed)
- 2 - 1460835 STUD-END COV
- 1 - 1837035 BRACKET AS
- 1 - 2N1287 ELBOW-FLARED
Action Required
Before Failure: Remove listed parts and install new parts according to the attached Rework Procedure.
After Failure: Remove the cracked housing and listed parts and install new housing and parts according to instructions.
Service Claim Allowances
Parts Disposition
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
Attach.
- (1-Rework Procedure)
Rework Procedure
Installation of Compressor Support
Current Configuration of Compressor Assembly, PA-8926, W2000 Road Milling Machine.
1) Remove Fuel Manifold, 103-4656, from Bracket As., 141-9308, leave hoses attached to manifold. Discard bolts, and keep washers for installation in STEP 9.
2) Remove Bracket As., 141-9308, keep bolts, 0S-1571 (3), for reinstallation in STEP 6.Discard Bracket As., washers, 5M-2894 (4), and Bolt 0S-1591 (1).
3) Disconnect Hose As.,101-6596, from fitting, 2N-1287, on rear of compressor. The Hose As. will be reinstalled in STEP 8.
4) Remove both bolts or existing studs nearest to the block on the rear of the compressorand discard.
5) Install (2) 146-0835 studs on back of compressor.Insert end of stud with 15 mm of thread into compressor Tighten to 20 N-m, reference tightening specs on 184-2514.
6) Place Bracket As., 183-7035, as shown on Assembly dwg. 184-2514.Reuse Bolts 0S-1571 (3) from STEP 2 and shipped bolt 0S-1571(1) and washers 9x-6458 (4).Reference tightening torque, and sequence to avoid breaking studs. Bracket 183-7035 Assembled
Bracket 183-7035 Assembled
7) Remove Fitting 2N-1287 from rear plate of compressor. Install new fitting 2N-1287 at a 10 degree angle to the vertical axis of the compressor.
8) Couple Hose As., 101-6596, to fitting,2N-1287.Hose should not interfere with Bracket As 183-7035.
9) Reinstall Fuel Manifold removed in STEP 1, use existing washersand new bolts 0T-0573.End of installation procedure.
