Exhaust Manifold
Show/hide table
图 1 | g06144387 |
发动机俯视图 |
Show/hide table
图 2 | g03363038 |
拧紧顺序 |
Show/hide table
技术规格,用于 380-8511 排气歧管总成 | |||
---|---|---|---|
项目 | 数量 | 零件 | 技术规格说明 |
1 | 2 | 133-3359 排气歧管 | 组装前,向凸端岐管的外径和凹端岐管的内径涂抹一薄层 2P-2333 高温密封胶。 去除组装好的接头上的多余密封胶。 |
2 | 12 | 106-1792 锥形锁紧螺柱 | 拧紧至扭矩为 |
3 | 2 | 6V-5843 螺栓 | 拧紧至扭矩为 |
4 | 1 | 380-8545 排气歧管 | 组装前,向凸端岐管的外径和凹端岐管的内径涂抹一薄层 2P-2333 高温密封胶。 去除组装好的接头上的多余密封胶。 |
5 | 4 | 357-0351 锥形锁紧螺柱 | 拧紧至扭矩为 |
6 | 12 | 2N-2766 锁紧螺母 | 在装配前,向螺纹和轴承表面涂覆 Loctite C5A 铜防咬合剂。
1. 按照图 2 中所示的数字顺序将锁紧螺母拧紧至扭矩为 2. 再次按照图 2 中所示的数字顺序将锁紧螺母拧紧至扭矩为 |
Caterpillar Information System:
Marine Engine and Genset Control Panel IIIB DCU Panel Symptoms
Marine Engine and Genset Control Panel IIIB Remote Panel Symptoms
G3500H Generator Set Engine Inlet Air Is Restricted
C175 Tier 4 Final Engines for Off-Highway Trucks Self-Cleaning Oil Filter Operation
A New Engine Oil Pump Is Now Used for Certain C175-16 Marine Engines {1154, 1304} A New Engine Oil Pump Is Now Used for Certain C175-16 Marine Engines {1154, 1304}
Procedure to Convert the Marine Auxiliary Diesel Electric Power (DEP) C280-16 Engine to a Main Propulsion Conversion C280-16 Engine {1051, 1052, 108D, 1152, 1205, 1302, 1307, 1308, 1319, 1326, 1403, 1901, 7490} Procedure to Convert the Marine Auxiliary Diesel Electric Power (DEP) C280-16 Engine to a Main Propulsion Conversion C280-16 Engine {1051, 1052, 108D, 1152, 1205, 1302, 1307, 1308, 1319, 1326, 1403, 1901, 7490}
Installation Procedure for the Pump Electronic Monitoring System for Well Stimulation Pumps {6002, 7490} Installation Procedure for the Pump Electronic Monitoring System for Well Stimulation Pumps {6002, 7490}
New Monitor Software Is Now Available for Certain Cat® Products {7620} New Monitor Software Is Now Available for Certain Cat® Products {7620}
NOx Sensor Location Identification for C3.4B Engines Used on Certain Paving Compactors {108F, 1091} NOx Sensor Location Identification for C3.4B Engines Used on Certain Paving Compactors {108F, 1091}
Marine Engine and Genset Control Panel IIIB Starting and Stopping
SCR Retrofit Aftertreatment Maintenance Interval Schedule
C7.1 Engines and Generator Sets ARD Nozzle - Test
C15 and C18 Engines for Caterpillar Built Machines Piston and Rings
C15 and C18 Engines for Caterpillar Built Machines Water Lines
C15 and C18 Engines for Caterpillar Built Machines Turbocharger
C15 and C18 Engines for Caterpillar Built Machines Alternator Mounting
C7.1 Engines and Generator Sets ARD Nozzle Heater - Test
G3500H Generator Set Engine Configuration Parameters
3512E and 3516E Marine Engines Turbocharger - Install
C15 and C18 Engines for Caterpillar Built Machines Electronic Control Wiring Group
New Software Is Now Available For EMCP 4.1 and EMCP 4.2 Displays {7620} New Software Is Now Available For EMCP 4.1 and EMCP 4.2 Displays {7620}
Radiator Hose Leaks on Certain C1.5 and C2.2 Engines {1353} Radiator Hose Leaks on Certain C1.5 and C2.2 Engines {1353}
3512E and 3516E Marine Engines Aftercooler - Remove and Install
Marine Selective Catalytic Reduction (SCR) Retrofit Aftertreatment After Stopping Engine