Product Description
3516C 发动机是电控柴油发动机。 发动机配有电子单体喷油器。 发动机配备独立回路后冷式设备。
发动机的效率和发动机的性能取决于是否遵守正确操作和保养建议。 使用建议使用的燃油、润滑油和冷却液。 对空气滤清器、燃油系统、润滑系统和冷却系统的保养应给予特别的注意。 关于保养事项的更多信息，参考操作和保养手册, "保养周期表"。
Show/hide table
| 3516C 发动机技术规范 | |||
| 项目 | 3516C | ||
| 额定转速（rpm） | 1800转/分 | ||
| 气缸和布置 | 60 度 V 型 16 | ||
| 缸径 | |
||
| 冲程 | |
||
| 类型 | 4 冲程循环 | ||
| 压缩比 | 14.7:1 | ||
| 进气方式 | 涡轮增压式 | ||
| 涡轮增压空气的冷却方法 | 独立回路后冷 | ||
| 每缸排量 | |
||
| 总排量 | |
||
| 旋向（飞轮端） | 逆时针转动 | ||
| 燃油 | 请参阅操作和保养手册, "加注容量和建议"。 | ||
| 燃油喷射方法 | 电子燃油喷油器 | ||
| 起动方法 | 空气起动马达 | ||
| 排气背压（设计） | |
||
| 最大允许背压 | |
||
| 最大进气阻力 | |
||
Show/hide table
| |
| 图 1 | g00308357 |
|
3516C 发动机 (A) 进气阀 (B) 排气阀 (C) 飞轮 | |
Caterpillar Information System:
PG145 Transmission Oil Filter (Transmission)
PG145 Transmission Gear Pump (Transmission)
3512C HD and 3516C HD Class I Division 2 Hazardous Location Generator Sets Model View Illustrations
PG145 Transmission Torque Converter
PG145 Transmission Transmission Power Flow
PG145 Transmission Hydraulic System Schematic
PG145 Transmission Location of Hydraulic Components for Transmission System
PG145 Transmission Location of Electronic Components for Transmission System
PG145 Transmission General Information
C3.3B and C3.8 Engines for Caterpillar Built Machines Engine Does Not Crank
G3512 Generator Set Engines Generator Output Power - Test
3516E Engines Coolant Temperature Sensor - Remove and Install
3512C HD and 3516C HD Class I Division 2 Hazardous Location Generator Sets Plate Locations and Film Locations
C1.7 and C2.2 Industrial Engines Cylinder Head
3512C HD and 3516C HD Class I Division 2 Hazardous Location Generator Sets Product Lifting
3516E Engines for Caterpillar Built Machines Crankshaft
C12.9 Marine Engines Pistons and Connecting Rods - Assemble
3512C HD and 3516C HD Class I Division 2 Hazardous Location Generator Sets Control Panel - Cat Marine Power Display (MPD) Control Panel (If Equipped)
A Modified Procedure Is Now Used to Seal the Mating Surfaces of the Cylinder Block and the Gasket on C15 And C18 Engines {1100, 1124, 1201} A Modified Procedure Is Now Used to Seal the Mating Surfaces of the Cylinder Block and the Gasket on C15 And C18 Engines {1100, 1124, 1201}
C1.7 and C2.2 Industrial Engines Crankshaft
C12.9 Marine Engines Cylinder Liner - Remove and Install
3512C HD and 3516C HD Class I Division 2 Hazardous Location Generator Sets Monitoring System - Diagnostic Trouble Codes and Event Codes
3512C HD and 3516C HD Class I Division 2 Hazardous Location Generator Sets Configuration Parameters
3512C HD and 3516C HD Class I Division 2 Hazardous Location Generator Sets Before Starting Engine