Track
Show/hide table
| |
| Illustration 1 | g02725196 |
Show/hide table
| Specification for 383-4238 Track Gp | |||
|---|---|---|---|
| Item | Qty | Part | Specification Description |
| - | - | - | All joints of the link assembly must have flexibility even with a measurable end play of zero. Flexibility is the ability for movement from the weight of the link assembly. |
| Use the following procedure to tighten the track bolts: | |||
| 1. Tighten the track bolts to |
|||
| 2. Tighten the standard track bolts to an extra turn of 120 ± 5 degrees. | |||
| 3. Tighten the master link bolts to an extra turn of 180 ± 5 degrees. | |||
| - | - | - | The maximum assembly force for the track link assembly is |
| - | - | - | The reference setting force is |
| A | - | - | Distance between the bolt holes is |
| B | - | - | Distance between the bolt holes is |
| C | - | - | Distance between the bolt holes is |
| D | - | - | Distance between the bolt holes is |
| E | - | - | Protrusion at one end of the pin is |
Show/hide table
| |
| Illustration 2 | g02725198 |
|
View of area F | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| G | - | - | Distance from the end of the plug (1) to the surface of the stopper (2) is |
| H | - | - | Distance from the end of the pin (3) to the surface of the stopper (2) is |
| - | - | - | The plug (1) must not be recessed below the surface of the stopper (2) after assembly. |
| End play for the link assemblies is |
Caterpillar Information System:
New Software Is Available Engines and New Coolant Pressure Sensor Are Used on Certain C32 Marine Engines {1920} New Software Is Available Engines and New Coolant Pressure Sensor Are Used on Certain C32 Marine Engines {1920}
C175-20 Locomotive Engine System Pressure Release
{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101} {0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}
C1.7 and C2.2 Industrial Engines Flywheel - Remove and Install
XQ35 Rental Generator Set Safety Messages
C18 Generator Set Engines Diesel Exhaust Fluid Module - Assemble
A New Accumulator Studs And Washers Are Now Available For Certain 3512 Engines {1252, 1254} A New Accumulator Studs And Washers Are Now Available For Certain 3512 Engines {1252, 1254}
Two Piece Stay Rod Installation Instructions {5070, 5070} Two Piece Stay Rod Installation Instructions {5070, 5070}
Crankshaft Pre-Assembly Instructions for Well Stimulation Pumps {1202, 6002} Crankshaft Pre-Assembly Instructions for Well Stimulation Pumps {1202, 6002}
Power End Rebuild Inspection Checklist for Well Stimulation Pumps {1202} Power End Rebuild Inspection Checklist for Well Stimulation Pumps {1202}
Torque Chart for Well Stimulation Pumps {0650, 6002} Torque Chart for Well Stimulation Pumps {0650, 6002}
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Condition Switch (Switch to Ground) - Test
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Power Train Piston Motor (Propel)
C175-16 and C175-20 Locomotive Engines Turbocharger - Remove
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Water Spray Lines
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Fuel Tank
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Conveyor Swing)
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Water Spray Pump
C1.7 and C2.2 Industrial Engines Engine Lifting Bracket - Remove and Install
PVT110, PVT115 4V3 and PVT117 4V3 Photovoltaic Modules Operation Information
C175-16 and C175-20 Locomotive Engines Crankcase Breather - Remove and Install
Software Issues on Certain C175-16 Generator Set Engines {7620} Software Issues on Certain C175-16 Generator Set Engines {7620}
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Air Cleaner
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Fuel Tank