C175-16 Marine Engine Caterpillar


Inlet and Exhaust Valve Seat Inserts

Usage:

C175-16 M6A

Remove and Install

Removal Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
371-0351  Valve Seat Puller 
1P-0510  Driver Gp 

Start By:

  1. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install".


    NOTICE

    Keep all parts clean from contaminants.

    Contaminants may cause rapid wear and shortened component life.




    Illustration 1g01206653

  1. Turn over the cylinder head. Use Tooling (A) and remove valve seats (1) from the cylinder head.

Installation Procedure



    Illustration 2g01206654

  1. Lower the temperature of valve seats (1). Use Tooling (B) and a suitable hammer in order to install valve seats (1) into the cylinder head.

End By:

  1. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install".

Caterpillar Information System:

C12.9 Marine Engines Coolant Temperature Sensor - Remove and Install
G3500H Generator Set Engine Nitrogen Oxide Sensor - Calibrate
Air Shut-Off Groups (3406B/C) {1078} Air Shut-Off Groups (3406B/C) {1078}
Functionality, Troubleshooting, Inspection, and Replacement for the 111-4374 Valve As (Check Valve Assembly) on Certain 3500 Commercial and Machine Engines {1355, 1393} Functionality, Troubleshooting, Inspection, and Replacement for the 111-4374 Valve As (Check Valve Assembly) on Certain 3500 Commercial and Machine Engines {1355, 1393}
A New Valve Bridge and Seal Are Used on Certain G3600 Engines {1100, 1121} A New Valve Bridge and Seal Are Used on Certain G3600 Engines {1100, 1121}
New Engine Software Is Used for Certain 3500 Marine Engines {1920} New Engine Software Is Used for Certain 3500 Marine Engines {1920}
New Software for C175-20 Turbocharger Thrust Bearing Wear {1920} New Software for C175-20 Turbocharger Thrust Bearing Wear {1920}
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Solenoid Valve - Test
C12.9 Marine Engines Aftercooler Condensate Drain Valve - Inspect/Clean
Recycling Instructions For Photovoltaic Modules {1471} Recycling Instructions For Photovoltaic Modules {1471}
C12.9 Marine Engines Electronic Control Module - Remove and Install
C12.9 Marine Engines Fuel System - Prime
New Software is Available for Certain C1.5 and C2.2 Engines {1920, 7620} New Software is Available for Certain C1.5 and C2.2 Engines {1920, 7620}
Engine Air Cleaner Elements on Certain C7.1 Engines {1051, 1052, 1054} Engine Air Cleaner Elements on Certain C7.1 Engines {1051, 1052, 1054}
XQ35 Rental Generator Set Maintenance Interval Schedule
323F SA and 323F LN Excavator Boom/Stick/Bucket Combinations
New VIMS Software is Now Available On Certain Large Off-Highway Truck/Tractors {7490, 7600, 7601, 7610, 7620} New VIMS Software is Now Available On Certain Large Off-Highway Truck/Tractors {7490, 7600, 7601, 7610, 7620}
C175-16 Locomotive Engine Electrical Power Supply - Test
CG137-08 and CG137-12 Engines Refill Capacities
C175-16 Locomotive Engine Sensor Calibration Required - Test
C175-16 Locomotive Engines Overhaul (Major)
New Software Is Used on Certain G3520C Landfill Engines {1280, 1920} New Software Is Used on Certain G3520C Landfill Engines {1280, 1920}
C1.7 and C2.2 Industrial Engine Valve Position - Test
C1.7 and C2.2 Industrial Engine Speed Control (Analog) - Test
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.