Auxiliary Drive (Lower Left Hand)
Show/hide table
| |
| Illustration 1 | g06003336 |
|
Front view | |
Show/hide table
| Specification for 469-8196 Auxiliary Drive Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 1 | 470-6584 Pump Drive Shaft As | Diameter is |
| Width of the groove for the thrust washer is |
|||
| During assembly, flush the bushing with the pump drive shaft to |
|||
| 2 | 1 | 487-4303 Adapter As | During assembly, align the hole in the bushing with the adapter. |
| Bore of 127-5400 Bushing after assembly is |
|||
| Installation depth of 127-5400 Bushing is |
|||
| 3 | 1 | 199-2889 Idler Shaft | Diameter is |
| 4 | 2 | 259-4598 O-Ring Seal | Before assembly, lightly lubricate the bore with the fluid that is being sealed. |
| 5 | 2 | 7N-5246 Thrust Washer | Thickness is |
| 6 | 1 | 155-2307 Idler Gear As | Bore of 116-1365 Bearing after assembly is |
| Installation depth of the bearing is |
|||
| 7 | 1 | 235-3546 O-Ring Seal | Before assembly, lightly lubricate the bore with the fluid that is being sealed. |
| 8 | 1 | 164-4995 Washer Assembly | Thickness of 164-4996 Thrust Washer is |
| Protrusion of 7N-2047 Dowel is |
|||
| 9 | 1 | 440-1134 Cover As | During assembly, align the hole in the bushing with the adapter. |
| Bore of 127-5400 Bushing after assembly is |
|||
Caterpillar Information System:
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Starting Motor - Inspect
G3508J, G3516J, and G3520J Engines Exhaust Elbow - Remove and Install
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Wiring Harness (Short Circuit) - Test
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System Wiring Harness (Open Circuit) - Test
New Generator Set Software Gp Is Now Used on Certain C7.1 Generator Sets {7610, 7620} New Generator Set Software Gp Is Now Used on Certain C7.1 Generator Sets {7610, 7620}
C175-20 Locomotive Engine Event Codes
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215} NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
C1.7 and C2.2 Industrial Engines Gauges and Indicators
C18 Generator Set Engines Turbocharger - Remove and Install
G3508J, G3516J, and G3520J Engines Turbocharger - Install
C1.7 and C2.2 Industrial Engines Fluid Recommendations
C1.7 and C2.2 Industrial Engines Welding on Engines with Electronic Controls
C1.7 and C2.2 Industrial Engines Cooling System Water Temperature Regulator - Replace
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Stator Winding Temperature - Test
Improved ARD Heater Assemblies Are Now Used on Certain C9.3, C13, C15, and C18 Engines {4493} Improved ARD Heater Assemblies Are Now Used on Certain C9.3, C13, C15, and C18 Engines {4493}
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Walk-Around Inspection
C1.7 and C2.2 Industrial Engines General Hazard Information
C1.7 and C2.2 Industrial Engines Burn Prevention
C1.7 and C2.2 Industrial Engines Cooling System Coolant Sample (Level 1) - Obtain
C1.7 and C2.2 Industrial Engines Cooling System Coolant Sample (Level 2) - Obtain
3516E Generator Set Engines Engine Oil Lines
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Prelube Pump - Inspect
Two Piece Stay Rod Installation Instructions for Well Stimulation Pumps {5070} Two Piece Stay Rod Installation Instructions for Well Stimulation Pumps {5070}
New Software is Now Available for all Cat® Object Detection and Vision Applications on Certain Cat® Products {7610, 7620} New Software is Now Available for all Cat® Object Detection and Vision Applications on Certain Cat® Products {7610, 7620}