Crankshaft
Show/hide table
| |
| Illustration 1 | g06237320 |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 1 | 9 | 149-6031 Main Bearing As | Before you assemble the crankshaft into the cylinder block, lubricate the main bearings journals and thrust plates with clean engine oil. |
| 2 | 2 | 7C-6209 Thrust Plate | Before you assemble the crankshaft into the cylinder block, lubricate the main bearings journals and thrust plates with clean engine oil.
Thrust plates should be used only on center main bearing. |
| 3 | 8 | 2W-2288 Plug | Torque to |
| 4 | 32 | 7N-2003 Dowel | Protrusion (D) of the dowel is |
| 5 | 48 | 128-4845 Bolt As | Use the following procedure to tighten the bolts:
1. Before assembly, lubricate the bolt threads, the bolt shank, the washer, and the underside of the bolt head with molylube. 2. Tighten the bolts evenly to 3. Again, tighten each bolt for an additional angle of 120 ± 5 degrees. 4. Single wrench or single spindle bolt sequence by position outer, outer, and inner. |
| After assembly into cylinder block, end play of the new crankshaft is |
|||
Caterpillar Information System:
3516E Generator Set Engines Flywheel Housing
3516E Generator Set Engines Fuel Injector
G3508J, G3516J, and G3520J Engines Gas Pressure Regulator Solenoid - Remove and Install
G3508J, G3516J, and G3520J Engines Gas Pressure Regulator - Install
A New Coolant Elbow Assembly is Now Used on Certain C18 Marine Engines {1059} A New Coolant Elbow Assembly is Now Used on Certain C18 Marine Engines {1059}
G3508J, G3516J, and G3520J Engines Gas Pressure Regulator - Remove
3516B Generator Set with Dynamic Gas Blending Alternator Mounting
A New Fuel Valve Is Now Used for Certain G3500BPetroleum Engines and G3500H Electric Power Engines {1741, 5137} A New Fuel Valve Is Now Used for Certain G3500BPetroleum Engines and G3500H Electric Power Engines {1741, 5137}
797 Off-Highway Truck Link and Rear Cylinder (Suspension) - Check
New Software is Available for Certain C4.4 Engines {1920} New Software is Available for Certain C4.4 Engines {1920}
3500E Marine Engines Fuel Injector Mechanism
3516E Generator Set Engines Accessory Drive
3516E Generator Set Engines Engine Oil Filter
G3500H 60Hz Generator Sets Before Starting Engine
3516E Generator Set Engines Auxiliary Water Pump
G3500H 60Hz Generator Sets Starting the Engine
G3500H 60Hz Generator Sets Engine Operation
EMCP 4.4 Supervisory Control Panel Starting and Stopping
G3512 EPA Emergency and Non-Emergency Standby Generator Sets Generator Operation
New Crankshaft Seals Are Not Compatible with the Front Adapter on Certain 3500 Mechanical Unit Injection Machine Engines {1160, 1161} New Crankshaft Seals Are Not Compatible with the Front Adapter on Certain 3500 Mechanical Unit Injection Machine Engines {1160, 1161}
New Crankshaft Seals Are Not Compatible with the Front Adapter on Certain 3500 Mechanical Unit Injection Engines {1160} New Crankshaft Seals Are Not Compatible with the Front Adapter on Certain 3500 Mechanical Unit Injection Engines {1160}
New Copper Lead Main and Connecting Rod Bearings Are Available For Certain 3500 Diesel Commercial Engines {1202, 1225} New Copper Lead Main and Connecting Rod Bearings Are Available For Certain 3500 Diesel Commercial Engines {1202, 1225}
G3512 EPA Emergency and Non-Emergency Standby Generator Sets After Stopping Engine
G3508J, G3516J, and G3520J Engines Exhaust Bypass Valve - Remove and Install