Diesel fuel is chemically similar to the lubricants that are used in diesel engines. A slow fuel leak will blend the fuel into the oil. Normal operating temperatures may cause volatile parts of the fuel to vaporize. The fuel that remains in the oil is less volatile.
A closed cup flash test can be performed to detect fuel dilution. The flash test is designed to measure the volatile parts of the fuel that are remaining in the oil. Detecting less volatile fuel is difficult. The lack of volatility reduces the accuracy of the flash test.
Since the flash test does not accurately detect fuel dilution, do not use the flash test as the only measure of fuel dilution. Instead, verify the dilution by the following methods:
- Gas chromatograph fuel dilution test
- Oil viscosity
The test that uses a gas chromatograph is designed to measure fuel dilution in crankcase oils. The gas chromatograph can identify the small chemical differences between diesel fuel and lubricating oil. Even though the gas chromatograph provides a more accurate measure of fuel dilution, always verify the results with the viscosity test.
A significant level of fuel dilution reduces oil viscosity. If an unacceptable level of fuel dilution is suspected, the kinematic viscosity of the oil must be measured.
Fuel dilution that is greater than 4 percent will usually cause viscosity that is less than the specified viscosity grade. If the oil is still within the specified viscosity grade, fuel dilution is unlikely to have reached an unacceptable level. Use the following chart to determine if viscosity has reached the minimum acceptable level. The guidelines of viscosity in the chart are slightly less than the limits of the SAE viscosity grades. However, these guidelines still provide adequate engine protection.
| Viscosity Grade | Minimum Oil Viscosity at 100 °C with Fuel Dilution Greater Than 4% as Measured by a Gas Chromatograph | Action |
| 0W-40
5W-40 10W-40 15W-40 |
12.0 cSt | Investigate the cause of fuel dilution or reduce the engine oil change interval. |
| 0W-30
5W-30 10W-30 |
9.0 cSt |
Always verify fuel dilution by the combination of a viscosity test and a gas chromatograph test that gives a result of more than 4 percent.
- Electronic unit injector seals
- electronic unit injector tip
- Shaft seal for the high-pressure fuel pump
Note: The procedures have been listed in order of probability. Complete the procedures in order.
 |
|
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death. |
| NOTICE |
|---|
|
Contact with high-pressure fuel may cause personal injury or death. Wait 10 minutes after the engine has stopped to allow fuel pressure to purge before any service or repair is performed on the engine fuel lines. |
| Troubleshooting Test Steps | Values | Results |
|---|---|---|
1. Electronic Unit Injector Seals A. Check for signs of damage to the seals for the electronic unit injectors. |
Electronic unit injector seals |
Result: Electronic unit injector seals are damaged. Repair: Replace any damaged electronic unit injector seals. Drain and refill the engine oil. Refer to the Operation and Maintenance Manual, "Engine Oil and Filter - Change". Result: All electronic unit injector seals are OK. Proceed to Test Step 2. |
2. Electronic Unit Injector Tip A. Check for signs of damage to the electronic unit injectors. Check the electronic unit injector tip for cracks or breakage. |
Electronic unit injector tip |
Result: An electronic unit injector is damaged. Repair: Replace the electronic unit injector. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove" and Disassembly and Assembly, "Electronic Unit Injector - Install". Drain and refill the engine oil. Refer to the Operation and Maintenance Manual, "Engine Oil and Filter - Change". Result: All electronic unit injectors are OK. Proceed to Test Step 3. |
3. Shaft Seal for the High-Pressure Fuel Pump A. Check for fuel leakage around the shaft seal for the high-pressure fuel pump. |
High-pressure fuel pump shaft seal |
Result: Fuel is leaking past the shaft seal for the high-pressure fuel pump. Repair: There is a restriction in the return line to the fuel tank. Investigate the cause of the restriction and then repair the fuel line. Replace the high-pressure fuel pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove" and Disassembly and Assembly, "Fuel Injection Pump - Install". Replace the fuel filter. Refer to the Operation and Maintenance Manual for further information. Inspect the return pipe from the high-pressure fuel pump to the fuel tank. replace any pipes that have been damaged or distorted by hot fuel. Result: The shaft seal for the high-pressure fuel pump is OK. Contact the Dealer Solutions Network (DSN). |