Custom Event Is Not Present
系统运作描述:
用户完全无法查看自定义事件。
测试步骤 1. 确保配置自定义事件的事件输入功能
为在事件日志中显示自定义文本字符串,"事件输入功能 #X 可疑参数号"必须配置为一种称为"自定义事件"的特殊类型事件,且"故障模式标识符"必须设置为"状态(状况存在)"。 按主菜单按钮,导航到 "I/O 状态"屏幕,选择"查看",导航到"数字输入",然后导航到应编程设定的自定义事件输入,然后按"确定"。
预期结果:
"事件输入功能 #X 可疑参数号"配置为"自定义事件",且"事件输入功能 #X 故障模式标识符"配置为"状态"。
结果:
- 确定 - 设定点配置正确。 转至测试步骤 2。
- 异常 - 需要更改设定点。 您需要安全级别 2 权限,或访问 Cat ET 来更改这些设定点。 如果从控制面板显示器更改"可疑参数号"设定点,确保编程设定输入,使使用类型为"系统事件",事件参数为"其他"下的"自定义事件",故障类型为"状态"。
停止
测试步骤 2. 检查接线故障
- 从"主菜单"屏幕上,选择"查看",然后选择 "I/O 状态"。
- 激活输入。 确保相应的输入指示变化。
预期结果:
当拨动连接在正确的输入触针与非隔离输入蓄电池负极或隔离输入参考电压之间的开关时,根据切换的数字输入,"I/O 状态"屏幕指示从短横 (-) 变为数字或字母。 如果处于详细信息屏幕,则从"激活"变为"非激活"
结果:
- 确定 - EMCP 4 上的接线和指示正常。 转至测试步骤 3。
- 异常 - 接线需要纠正。
修复: 修理配线。 输入应连接在相应的数字输入触针与该输入的参考电压之间。
停止
测试步骤 3. 检查事件响应是否启用
每个事件,如"自定义事件 #1 条件存在",均具有相关联的事件响应配置。 必须启用事件的事件响应配置,以便显示在事件日志中。
预期结果:
您试图触发的特定自定义事件的"自定义事件 #X 条件存在事件响应配置"应设置为"警告"、"软停机"、"硬停机"或"仅激活"(其他设置可选)。
结果:
- 确定 - 已配置设定点。
修复: 请致电您的客户支持代表,获取进一步的帮助。
停止
- 异常 - 更改设定点。 您需要安全级别 2 权限,或访问 Cat ET 来更改此设定点。 尝试更改此设定点之前,确保 ECS 设置为停止。
停止
Caterpillar Information System:
EMCP4.2B Diagnostic Capabilities
EMCP4.2B Service Tools
EMCP4.2B General Information
EMCP4.2B Monitoring Software for Computer
EMCP4.2B Discrete Input/Output Module
EMCP4.2B Resistive Temperature Device Module
EMCP4.2B Thermocouple Module - EMCP 4.2 only
C1.7 and C2.2 Industrial Engine Engine Overspeeds
EMCP4.2B Annunciator Module
EMCP4.2B Integrated Voltage Regulator
EMCP4.2B Real Time Clock Programming - EMCP 4.2 only
C8.7 Marine Engine Magnetic Switch (Air Inlet Heater Relay) - Remove and Install
C1.7 and C2.2 Industrial Engine Engine Top Speed Is Not Obtained
3516B Generator Set Engines with Dynamic Gas Blending Injector Solenoid - Test
SRMP Electric Power Generation SRMP Generator Rotor - Remove and Install
C1.7 and C2.2 Industrial Engine Oil Contains Fuel
2015/09/17 Cat® Reman Announces Additions to Sea Water Pump Portfolios {1371}
2015/09/15 A Guide to Reman Product Markings is Now Available {7754}
2015/09/17 A Guide to Reman Product Markings is Now Available {7754}
2015/09/18 A Guide to Reman Product Markings is Now Available {7754}
2015/09/17 A Procedure to Use the Correct Mounting Bolts with the 10R-2356 Flywheel As is Available {1156}
2015/09/18 A Procedure to Use the Correct Mounting Bolts with the 10R-2356 Flywheel As is Available {1156}
2015/09/18 The Required Parts for Installing Turbochargers on Certain 2007 On-Highway Truck Engines Is Published {1052}
390F Excavator Stopping the Engine