Indicator Lamp Problem
- Burned out bulb
- Problem with the lamp circuit
- A system on the power train data link
Complete the procedure in the order in which the steps are listed.
Show/hide table
| Troubleshooting Test Steps | Values | Results |
|---|---|---|
1. Check the Circuit for the Lamp A. Check the electrical circuit for the lamp. B. Refer to Troubleshooting, "Indicator Lamp - Test". |
Lamp Circuit |
Result: The electrical circuit is OK. Proceed to Test Step 2. Result: The electrical circuit is not OK. Repair: Repair the circuit. Verify the repair. If the problem is not resolved, proceed to Test Step 2. |
2. Check the Systems on the Power Train Data Link A. A system that is connected to the power train data link may be illuminating the lamp. Check the systems that are connected to the power train data link. B. Obtain the necessary equipment, when possible. Monitor the appropriate parameters while the machine is experiencing problems. Determine if the condition is normal operation. |
Power Train Data Link |
Result: A system that is connected to the power train data link is illuminating the lamp. Repair: Troubleshoot the system causing the illumination of the lamp. Verify that the repair eliminated the problem. |
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Caterpillar Information System:
C2.2 Engines for Caterpillar Built Machines Temperature Sensor (Exhaust) - Remove and Install
C2.2 Engines for Caterpillar Built Machines Temperature Sensor (Catalyst Inlet) - Remove and Install
C2.2 Engines for Caterpillar Built Machines Secondary Engine Speed/Timing Sensor - Remove and Install
C2.2 Engines for Caterpillar Built Machines Primary Engine Speed/Timing Sensor - Remove and Install
Single Module Systems (SMS) Modbus and Paralleled Multiple Module Systems (PMMS) Modbus Register Maps for Use With APC1+{1926, 4490} Single Module Systems (SMS) Modbus and Paralleled Multiple Module Systems (PMMS) Modbus Register Maps for Use With APC1+{1926, 4490}
Cat® Command For Hauling MID 039 - CID 3244 - FMI 05
Cat® Command For Hauling MID 039 - CID 3244 - FMI 03
G3606 and G3608 Engines Fuel Control Valve - Remove and Install
2015/05/01 Resistor Gp May Need To Be Added When Monitoring Systems Are Replaced By EMS-III On Certain Cat® Engines {1408, 7490}
C2.2 Engines for Caterpillar Built Machines Exhaust Elbow - Remove and Install - Exhaust Elbow between the Turbocharger and the Clean Emissions Module (CEM)
2015/04/03 A New Fuel Gas Valve Is Used For Certain G3500 Engines {1270, 1408, 1741}
C9.3 Marine Propulsion Engine Fuel Temperature Is High
C9.3 Marine Auxiliary and Generator Set Engine Inlet Air Is Restricted
Replacement Parts Guide For The Fuel Control Valve Fuel System Components On Certain G3500 Engines{1274, 5137} Replacement Parts Guide For The Fuel Control Valve Fuel System Components On Certain G3500 Engines{1274, 5137}
Cat® Command For Hauling MID 039 - CID 3244 - FMI 06
G3606 and G3608 Engines Exhaust Bypass - Remove and Install
C9.3 Marine Auxiliary and Generator Set Engine Intake Manifold Air Temperature Is High
C9.3 Marine Auxiliary and Generator Set Engine Oil Consumption Is Excessive
2015/07/07 A New Nozzle Ring Is Used on Certain G3508 and G3516B Engines {1052}
3516C Locomotive Engine Maintenance Interval Schedule
C9.3 Marine Auxiliary and Generator Set Engine Oil Contains Coolant
3500C Independent Power Producer Packaged Generator Set Engines Are Experiencing High Oil Consumption{1000, 1318, 1348, 7500} 3500C Independent Power Producer Packaged Generator Set Engines Are Experiencing High Oil Consumption{1000, 1318, 1348, 7500}
C9.3 Marine Auxiliary and Generator Set Engine Oil Contains Fuel
C4.4 Engines Glow Plug Starting Aid - Test