Nitrogen Oxide Sensor - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Loctite Nickel Anti-seize | - |
Show/hide table
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool. |
- Remove cable straps (1) from bracket (2).
- Remove nitrogen oxide sensor (3).
Show/hide table
Illustration 2 g03771506 - Disconnect nitrogen oxide sensor (3).
Show/hide table
Illustration 3 g03771696 - Remove cable straps (4) and disconnect nitrogen oxide sensor (5).
Show/hide table
Illustration 4 g03771744 - Remove nitrogen oxide sensor (5).
Show/hide table
Illustration 5 g03772716 - Remove bolts (7) and bracket (6).
Show/hide table
Illustration 1 | g03771300 |
Note: New nitrogen oxide sensors are pre-lubricated. Do not use Tooling (A) on new nitrogen oxide sensors. When installing an existing nitrogen oxide sensor install Tooling (A) on the threads only.
Note: For more information about nitrogen oxide sensors, refer to Special Instruction, REHS8151, "NOx Sensors Handling and Installation Procedures"
- Install nitrogen oxide sensors (3) and (5) in the reverse order of removal.
- Tighten nitrogen oxide sensors (3) and (5) to a torque of
50 ± 10 N·m (37 ± 7 lb ft) .
- Tighten nitrogen oxide sensors (3) and (5) to a torque of
Caterpillar Information System:
XQ400 Power Module Engine Air Cleaner Element (Dual Element) - Inspect/Clean/Replace
C3.4B Engines Idle Validation - Test
Caterpillar Communication Regarding REACH Article 33{0374, 7000} Caterpillar Communication Regarding REACH Article 33{0374, 7000}
C7.1 Engines Engine Overspeeds
C7.1 Engines Engine Misfires, Runs Rough or Is Unstable
C11 and C13 Engines Crankshaft Rear Seal - Install
C11 and C13 Engines Crankshaft Rear Seal - Remove
C13 Industrial Engine Air Control Valve - Remove and Install
C4.4 and C7.1 Engines Engine Has Mechanical Noise (Knock)
C4.4 and C7.1 Engines Engine Has Early Wear
C4.4 and C7.1 Engines Engine Does Not Crank
C7.1 Engines Engine Cranks but Does Not Start
C13 Industrial Engine Fumes Disposal Filter Element - Replace - If Equipped
464-0265 Lifting Bracket Assembly{0374, 0599, 0629, 0632, 0700, 0708, 1353} 464-0265 Lifting Bracket Assembly{0374, 0599, 0629, 0632, 0700, 0708, 1353}
XQC1200 Power Module Engine Air Cleaner Service Indicator - Inspect
Engine Speed May Elevate Unexpectedly on Certain Commercial Engines{1920} Engine Speed May Elevate Unexpectedly on Certain Commercial Engines{1920}
2014/12/12 An Improved Wiring Harness Is Used on Certain G3600 Engines {1408}
2014/12/19 New Tube Assemblies Are Used on Certain G3600 Engines {1070, 1350}
Caterpillar Petroleum Well Service Transmission Installation Appraisal Procedures{1400, 3030} Caterpillar Petroleum Well Service Transmission Installation Appraisal Procedures{1400, 3030}
C7.1 Engines Engine Shutdown Occurrence
XQ375 and XQ425 Rental Generator Sets Plate Locations and Film Locations
C3.4B Engines Indicator Lamp - Test
XQ375 and XQ425 Rental Generator Sets Product Lifting
C13 Generator Set Engine Atmospheric Pressure Sensor - Remove and Install