Engine Oil Pan - Remove and Install - C18 Engine
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | Loctite 蓝色 RTV 有机硅 | - |
B | 1Y-3904 | 粘接剂 | - |
- 将发动机机油排入合适的容器以便保存或弃置。 请参阅操作和保养手册, "发动机机油和滤清器 - 更换"。 将 O 形密封圈从排放螺塞上拆下。
- 拆下螺栓 (1) 后拆下油底壳 (2)。
Show/hide table
图 2 g03393689 - 将密封垫 (3) 从油底壳上拆下。
Show/hide table
图 3 g03393739 Show/hide table图 4 g03393741 - 如有必要,拆下螺栓 (4) 并分离油底壳的两部分。 拆下密封垫 (5)。
Show/hide table
图 1 | g03393688 |
- 如有必要,安装新的垫片 (5) 并连接油底壳的两部分。 安装螺栓 (4) 并用手拧紧。
注: 下一步安装应当在涂抹工具 (A) 后的 10 分钟内执行。
Show/hide table图 7 g03393747 - 将工具 (A) 涂抹到位置 (Z) 的接头上。
- 将工具 (B) 涂抹到位置 (Y)。
- 将新密封垫 (3) 安装到油底壳 (2) 上。 将工具 (A) 涂抹到位置 (Z)。
Show/hide table
图 8 g03393688 - 安装油底壳 (2)。 安装螺栓 (1) 并用手带紧。
Show/hide table
图 9 g03393802 注: 如果油底壳的两部分没有分离,转至步骤 7
- 按照图 9 中所示的顺序将螺栓 (4) 拧紧至扭矩为
47 ± 9 N·m (35 ± 7 lb ft) ,然后将螺栓 (4) 重新拧紧至扭矩为47 ± 9 N·m (35 ± 7 lb ft) 。Show/hide table图 10 g02463392 螺栓 (1) 的上紧顺序。 - 根据图 10 内的顺序 (A) 将螺栓 (1) 上紧到
40 ± 5 N·m (30 ± 4 lb ft) 的扭矩。 - 根据图 10 内的顺序 (B) 将螺栓 (1) 重新上紧到
47 ± 5 N·m (35 ± 4 lb ft) 的扭矩。 - 加注发动机油底壳至发动机油尺上显示的正确油位。 请参阅操作和保养手册, "加注容量和建议",以了解发动机的润滑系统容量。
Show/hide table
图 5 | g03393741 |
Show/hide table
图 6 | g03393739 |
Caterpillar Information System:
TA2 Technical Inspection for 3512C Dynamic Gas Blending Oil Well Service Engines {0372, 1000, 753T} TA2 Technical Inspection for 3512C Dynamic Gas Blending Oil Well Service Engines {0372, 1000, 753T}
3516C Petroleum Engines Exhaust Elbow - Remove and Install
349F and 352F Excavators Hydraulic System Gear Pump (Pilot) - Test
349F and 352F Excavators Hydraulic System Travel Motor - Test - Measurement of Case Drain Oil
349F and 352F Excavators Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
C7.1 Marine Generator Set Heat Exchanger - Inspect
C7.1 Marine Generator Set Engine Oil and Filter - Change - Duplex Oil filters
C7.1 Marine Generator Set Fuel System Primary Filter (Water Separator) Element - Replace
3512C Petroleum Engines with Dynamic Gas Blending Fuel Actuator - Test
3512E Tier 4 Final Engines for Land Electric Drilling Sensor Supply - Test
Failure of 12 Volt Electrical Power Converter on Certain Off-Highway Trucks{1408, 1421} Failure of 12 Volt Electrical Power Converter on Certain Off-Highway Trucks{1408, 1421}
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Camshaft Bearing Position
3516C Petroleum Engines Exhaust Manifold - Remove and Install
2014/05/16 New Water Pump Seal and Pumps Used on Certain 3500, G3500, and C175 Engines {1361, 7555}
New Water Pump Seal and Water Pumps Are Used on Certain 3500 and G3500 Engines {1361} New Water Pump Seal and Water Pumps Are Used on Certain 3500 and G3500 Engines {1361}
C7.1 Marine Generator Set Coolant Sample (Level 1) - Obtain
C175-16 and C175-20 Engines for Off-Highway Trucks Connecting Rod Bearings
C13, C15, and C18 Tier 4 Final Engines Coolant Level Sensor
C7.1 Industrial Engine Product Storage
C32 Generator Set Voltage Regulators - R450T Automatic Voltage Regulator (AVR)
C175-16 Locomotive Engine Engine Oil Temperature Sensor
2013/06/13 New Injection Assemblies Are Equipped with Flow Indicators for Certain Retrofit Selective Catalytic Reduction Systems {108I}
C15 and C18 Engines for Caterpillar Built Machines Valve Mechanism Cover Base - Remove and Install
C7.1 Marine Generator Set Reference Material