Crankshaft Main Bearings - Remove
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 9S-9082 | Engine Turning Tool | 1 |
B | 9U-5023 | Main Bearing Wrench | 1 |
C | 2P-5517 | Main Bearing Tool | 1 |
D | 230-5843(1)
or 236-6688(2) |
Main Bearing Cap Tool | 2 |
Show/hide table
(1) | Use with |
(2) | Use with |
Start By:
- Remove the oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove covers (1) from the side of the engine.
- Use Tooling (A) in order to rotate the crankshaft. Rotate the crankshaft in order to position the counterweight on the top.
Show/hide table
Illustration 2 g00930580 - Use Tooling (B) and loosen the bolts for the main bearing cap.
Show/hide table
Illustration 3 g00930589 - Remove the two outer bolts for main bearing cap (2) and install Tooling (D). Install Tooling (D) until Tooling (D) bottoms out in the block. Adjust nuts (3) on Tooling (D) until nuts (3) make contact with main bearing cap (2). Remove the two inner bolts for main bearing cap (2).
Show/hide table
Illustration 4 g00930593 - Loosen nuts (3) evenly in order to lower main bearing cap (2). Lower main bearing cap (2) to the end of the bolt on Tooling (D) in order to gain access to the main bearings.
Show/hide table
Illustration 5 g00930603 - Use Tooling (A) and rotate the crankshaft until the oil hole of the crankshaft journal is just below the side of the main bearing without the tab. Install Tooling (C) and remove the upper bearing.
Show/hide table
Illustration 6 g00930606 - Remove lower main bearing (4) from main bearing cap (2).
Show/hide table
Illustration 1 | g00930577 |
Caterpillar Information System:
3516B Engine Connecting Rod Bearings - Remove and Install
3516B Engine Bearing Clearance - Check
3516B Engine Piston Cooling Jets - Remove and Install
3516B Engine Gear Group (Rear) - Install
C175-16 and C175-20 Generator Set Engines Turbocharger
2012/12/10 A Revised Application and Installation Guide Is Now Available for Certain Industrial Engines {1000}
C175-16 and C175-20 Generator Set Engines Turbocharger
C175-16 and C175-20 Generator Set Engines Turbocharger
C175-16 and C175-20 Generator Set Engines Turbocharger
C175-16 and C175-20 Generator Set Engines Engine Oil Pan
C175-16 and C175-20 Generator Set Engines Engine Oil Pan
C32 Auxiliary Engine Control Panel - Cat Marine Engine Control Panel I (MECP I) (If Equipped)
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Wiring Harness (Open Circuit) - Test
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Wiring Harness (Short Circuit) - Test
C18 Marine Engine Configuration Parameters
349F and 352F Excavators ECM Software - Install
349F and 352F Excavators ECM - Configure
C18 Marine Auxiliary and Marine Generator Set Engines Exhaust Has Excessive White Smoke
C175-16 and C175-20 Generator Set Engines Pressure Control Valve - Oil Regulator Valve and Oil Bypass Valve
C175-16 and C175-20 Generator Set Engines Engine Oil Pan
C175-16 and C175-20 Generator Set Engines Oil Pump
C175-16 and C175-20 Generator Set Engines Air Lines
C175-16 Locomotive Engine Water Pump
C175-16 Locomotive Engine Air Lines