Oil Pump
Show/hide table
| |
| Illustration 1 | g03176936 |
Show/hide table
| Specification for 340-9261 Engine Oil Pump Gp | |||
| Item | Qty | Part | Specification Description |
| Before you install the pump, lubricate the moving parts with clean engine oil. Rotate the pump by hand in order to ensure that the pump rotates freely. | |||
| 1 | 1 | 340-9262 Drive Shaft As | Diameter is Distance (B) from end of the shaft to gear face is |
| 2 | 1 | 266-5370 Oil Pump Shaft Assembly | Diameter is Distance (C) from end of the shaft to gear face is |
| 3 | 2 | 266-5372 Gear | Length of the new gear is Depth of the bore in the oil pump body for new gear is Before installation, bore in the gear for shaft assemblies is |
Show/hide table
| |
| Illustration 2 | g03176937 |
|
266-5366 Oil Pump Body As | |
Show/hide table
| Item | Qty | Part | Specification Description |
| E | - | - | Position for the bushing joints from the centerline through the bushing bores of the oil pump body assembly is 30 ± 15 degrees. |
| 4 | 1 | 262-0562 Bushing | After installation, bore in the bushing for oil pump drive shaft assembly is Installation depth (F) is |
| 5 | 1 | 255-4854 Bushing | After installation, bore in the bushing for oil pump shaft assembly is Installation depth (F) is |
Show/hide table
| |
| Illustration 3 | g03176938 |
|
255-4842 Oil Pump Cover | |
Show/hide table
| Item | Qty | Part | Specification Description |
| H | - | - | Position for the bushing joints from the centerline through the bushing bores of the oil pump cover is 30 ± 15 degrees. |
| 6 | 1 | 255-4854 Bushing | After installation, bore in the bushing for oil pump shaft assembly is Installation depth (J) is |
| 7 | 1 | 262-0562 Bushing | After installation, bore in the bushing for oil pump drive shaft assembly is Installation depth (J) is |
| K | 2 | 7N-5683 Dowel | Extension of dowels from the oil pump cover is |
Caterpillar Information System:
C175-16 and C175-20 Generator Set Engines Engine Oil Pan
C175-16 and C175-20 Generator Set Engines Pressure Control Valve - Oil Regulator Valve and Oil Bypass Valve
C18 Marine Auxiliary and Marine Generator Set Engines Exhaust Has Excessive White Smoke
349F and 352F Excavators ECM - Configure
349F and 352F Excavators ECM Software - Install
C18 Marine Engine Configuration Parameters
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Wiring Harness (Short Circuit) - Test
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Wiring Harness (Open Circuit) - Test
3516B Engine Crankshaft Main Bearings - Remove
3516B Engine Connecting Rod Bearings - Remove and Install
3516B Engine Bearing Clearance - Check
3516B Engine Piston Cooling Jets - Remove and Install
C175-16 and C175-20 Generator Set Engines Air Lines
C175-16 Locomotive Engine Water Pump
C175-16 Locomotive Engine Air Lines
C175-16 and C175-20 Generator Set Engines Flywheel
CEM Locomotive Aftertreatment Overhaul (Top End)
3516C Locomotive Engine and Generator Set Overhaul (In-Frame)
3516C Locomotive Engine and Generator Set Flexible Coupling Oil - Change - If Equipped
C175-16 and C175-20 Generator Set Engines Flywheel
C175-16 Locomotive Engine Pressure Sensor
Cat Water Delivery System (WDS) Fuses - Replace
Cat Water Delivery System (WDS) Hydraulic Oil Cooler - Clean
2012/08/10 Improved Locknuts for the High Pressure Turbocharger to Exhaust Manifold Joint Are Used on Certain Commercial Engines {1052}