Piston and Rings
Show/hide table
Illustration 1 | g03164417 |
Show/hide table
Specification for 319-7945 Piston and Rod Gp     | |||
Item     | Qty     | Part     | Specification Description     |
1     | 1     | 314-2691 Piston Ring     | Install the top piston ring with the side marked "UP" toward top of the piston. Orient the red color stripe face to the right of the piston ring end gaps.     |
Clearance between the ends of the top piston ring is 1.15 ± 0.15 mm (0.045 ± 0.006 inch). |
|||
Width of groove in new piston body assembly for piston ring is 6.170 to 6.200 mm (0.2429 to 0.2441 inch). |
|||
Thickness is 5.975 to 5.990 mm (0.2352 to 0.2358 inch). |
|||
2     | 1     | 314-2692 Piston Ring     | Install the intermediate piston ring with the side marked "UP" toward top of the piston. Orient the black color stripe face to the right of the piston ring end gaps.     |
Clearance between the ends of the intermediate piston ring is 1.95 ± 0.15 mm (0.077 ± 0.006 inch). |
|||
Width of groove in new piston body assembly for piston ring is 6.140 to 6.170 mm (0.2417 to 0.2429 inch). |
|||
Thickness is 5.975 to 5.990 mm (0.2352 to 0.2358 inch). |
|||
-     | -     | -     | After the piston rings have been installed, rotate the piston rings so that the end gaps are 120 ± 20 degrees apart from each other.     |
3     | 1     | 314-2693 Oil Ring     | The ends of the oil control piston ring should be at a distance of 180 degrees from the ring end gap when the oil control piston ring is assembled. The white color stripe of oil ring spring should be visible at oil ring end gap.     |
Clearance between the ends of the new oil control piston ring is 0.15 ± 0.10 mm (0.006 ± 0.004 inch). |
|||
Width of groove in new piston body assembly for piston ring is 8.040 to 8.060 mm (0.3165 to 0.3173 inch). |
|||
Thickness is 7.965 to 7.987 mm (0.3136 to 0.3145 inch). |
|||
4     | 1     | 7C-1412 Piston Pin     | Thoroughly lubricate the piston pin with clean engine oil before the piston pin is inserted into the piston body assembly and the rod assembly.     |
Outside diameter is 119.994 ± 0.006 mm (4.7242 ± 0.0002 inch). |
|||
Length is 249.75 ± 0.25 mm (9.833 ± 0.010 inch). |
|||
Bore in the new piston body assembly for the piston pin is 120.015 to 120.035 mm (4.7250 to 4.7258 inch). |
|||
5     | 2     | 7C-1413 Pin Retainer     | Install the pin retainer with the word "OUT" is visible. After assembly, maintain a minimum clearance of 0.05 mm (0.002 inch) between piston pin and pin retainer.     |
Show/hide table
Illustration 2 | g03164456 |
Show/hide table
Specification for 319-7945 Piston and Rod Gp     | |||
Item     | Qty     | Part     | Specification Description     |
6     | 1     | 314-2696 Bolt     | Use the following procedure in order to tighten the bolt: 1. Lubricate the thread and supporting surface of bolt with Molykote Paste G-n Plus. 2. Tighten bolt to 160 N·m (118 lb ft). 3. Loosen the bolt. 4. Again, tighten bolt to 40 N·m (30 lb ft). 5. Again, tighten to an additional angle of 90 degrees. The bolt is reuseable if, overall length of the bolt is less than 81.4 mm (3.20 inch).     |
Caterpillar Information System:
C280-16 Petroleum Engine Air Lines
C280-16 Petroleum Engine Oil Mist Detector
C280-16 Petroleum Engine Camshaft Bearings
C32 Marine Engines Aftercooler - Remove
3516B Engine Engine Oil Scavenge Pump - Disassemble
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Timing - Calibrate
C18 Marine Engine Coolant - Change
Exciter Rotor Is Loosening on Certain 3512, and C32 Generator Sets{4454} Exciter Rotor Is Loosening on Certain 3512, and C32 Generator Sets{4454}
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators System Accuracy - Test
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Pressure Sensor - Calibrate
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators System - Calibrate
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators System - Set
C280-16 Petroleum Engine Fuel Injection Lines
C280-16 Petroleum Engine Air Starting Control
C280-16 Petroleum Engine Turbocharger Oil Lines
C280-16 Petroleum Engine Connecting Rod
C280-16 Petroleum Engine Exhaust Bypass
C280-16 Petroleum Engine Exhaust Manifold
C280-16 Petroleum Engine Engine Mount
C175-16 Locomotive Engine Turbocharger Turbine Temperature Is High
3516B Engine Engine Oil Scavenge Pump - Assemble
C280-16 Petroleum Engine Inlet Manifold Air Pressure Sensor
3516B Engine Valve Mechanism Cover - Remove and Install
3516B Engine Valve Mechanism Cover Base - Remove and Install