Fuel Manifold - Remove and Install - Return
- Remove tube assemblies (3) and remove clip (1).
- Remove fuel manifold (2).
Show/hide table
Illustration 2 g02796498 - Remove connector (4) and the O-ring seal. Remove plug (6).
- Remove check valve (5).
Show/hide table
Illustration 3 g02796509 - Remove check valve (7) and the O-ring seal. Remove O-ring seal (9) and backup ring (8).
Show/hide table
Illustration 1 | g02796484 |
- Install fuel manifold (2) in the reverse order of removal.
- Tighten check valve (7) to a torque of
28 ± 3 N·m (21 ± 2 lb ft) .
- Tighten check valve (7) to a torque of
Caterpillar Information System:
C9.3 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install
C9.3 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
C175-16 and C175-20 Generator Set Engines Fuel Rail Temperature Is High
G3500 Generator Sets Maintenance Interval Schedule - Prime
Using the TMI System to Retrieve Off Engine Injection Pump Test Specifications for the Fuel Injection Equipment Test Stand{0706, 0782, 1251, 1286} Using the TMI System to Retrieve Off Engine Injection Pump Test Specifications for the Fuel Injection Equipment Test Stand{0706, 0782, 1251, 1286}
2012/03/02 Improved Turbocharger Oil Drain Tubes Are Used on Certain C18 and 3406E Commercial Engines {1052, 1307}
2011/12/15 Procedure to Remedy Loose V-belts on Certain C18 and C32 Marine Engines {1207, 1358, 1359, 1397}
2014/07/07 An Improved Guide Spring and Valve Lifter Assembly Are Used in Certain C-9, C9 ACERT Engines, and C9.3 ACERT Engines {1108}
2011/12/22 A New O-ring and Oil Pan Drain Plug Are Now Used on Certain C12 Marine Engines {1302, 7553, 7555}
2011/12/19 Use the FT3193 Harness Assembly to Communicate with the Adem II 6X/6U ECM on Certain Industrial Engines {1408, 1901}
2011/12/19 Use the FT3193 Harness Assembly to Communicate with the Adem II 6X/6U ECM on Certain Truck Engines {1408, 1901}
D Series Excavator Monitoring System Configuration Mode
C9.3 Engines for Caterpillar Built Machines Relief Valve (Fuel) - Remove and Install
Using the 265-4177, 265-4209 Service Tool Groups to Install Sensors in Position-Sensing Hydraulic Cylinders{0599, 0709, 0738, 1439, 7562, 7562} Using the 265-4177, 265-4209 Service Tool Groups to Install Sensors in Position-Sensing Hydraulic Cylinders{0599, 0709, 0738, 1439, 7562, 7562}
G3500 Generator Sets Maintenance Interval Schedule - Landfill
C9.3 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove and Install
2012/07/20 New High-Pressure Fuel Pumps Are Used for C175 Off-Highway Truck Engines {1251}
2012/07/19 New High-Pressure Fuel Pumps Are Used for C175-16 Engines {1251}
C15 and C18 Engines for Caterpillar Built Machines Ignition Coil - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines DEF Injector and Mounting - Remove and Install
C15 Petroleum Generator Set Fluid Recommendations
2012/01/24 A New Bolt and Washer Are Used in the Bracket for the Fuel Injection Supply Lines on C175-16 Engines {1252, 7553}
C15 and C18 Engines for Caterpillar Built Machines Combustion Head - Remove and Install
C15 Petroleum Generator Set After Starting Engine