Cylinder Head Valves
Show/hide table
图 1 | g02557379 |
Show/hide table
328-7083 缸盖总成技术规格 | |||
项目 | 数量 | 零件 | 技术规格说明 |
1 | 4 | 318-4785 弹簧 | 在试验力下的长度为 |
试验力为 |
|||
试验后的自由长度为 |
|||
2 | 4 | 318-4786 弹簧 | 在试验力下的长度为 |
试验力为 |
|||
试验后的自由长度为 |
|||
3 | 4 | 236-0544 气门导管 | 注:组装到缸盖前,将清洁的发动机机油涂敷到气门导管的外径上。 |
至气门导管顶部的高度 (A) 是 |
|||
安装后,进气门新气门导管中的孔径是 |
|||
4 | 2 | 273-1224 进气门 | 注:组装到气门导管前,将清洁的发动机机油涂敷到气门杆上。 |
气门杆直径为 |
|||
气门头 (B) 的直径是 |
|||
气门端面角度为 70.75 ± 0.25 度。 | |||
5 | 2 | 254-2073 排气门 | 注:组装到气门导管前,将清洁的发动机机油涂敷到气门杆上。 |
气门杆直径为 |
|||
气门头 (C) 的直径是 |
|||
气门端面角度为 45.60 ± 0.25 度。 | |||
6 | 2 | 333-9179 气门座镶圈 | 气门座镶圈端面角度是 20.00 ± 0.25 度。 |
进气门座镶圈的外径为 |
|||
缸盖中用于安装进气门座镶圈的孔径为 |
|||
缸盖中用于安装气门座镶圈的孔的深度为 |
|||
7 | 2 | 333-9180 气门座镶圈 | 气门座镶圈端面角度是 45.00 ± 0.25 度。 |
排气门座镶圈的外径为 |
|||
缸盖中用于安装排气门座镶圈的孔径为 |
|||
缸盖中用于安装气门座镶圈的孔的深度为 |
Caterpillar Information System:
CG137-08 and CG137-12 Engines Plate Locations and Film Locations
Network Management Card and Network Management Card with Environmental Monitoring for the UPSB505 Uninterruptible Power Supply Environmental Monitoring
Network Management Card and Network Management Card with Environmental Monitoring for the UPSB505 Uninterruptible Power Supply UPS Monitor and Configure
3516C Generator Set Engines Intake Manifold Air Temperature Is High
C13, C15, and C18 Tier 4 Final Engines Flywheel
Blow-by from Crankcase Breather for C2.2, C3.3, C4.4, C6.6, C7.1 (Mechanical), and C7.1 Engines {1000, 1074, 1107, 1317} Blow-by from Crankcase Breather for C2.2, C3.3, C4.4, C6.6, C7.1 (Mechanical), and C7.1 Engines {1000, 1074, 1107, 1317}
C13, C15, and C18 Tier 4 Final Engines Flywheel
C13, C15, and C18 Tier 4 Final Engines Flywheel
3500 Engines Air Shutoff
C9.3 Tier 4 Final Engines Exhaust Diffuser Adapter
C13, C15, and C18 Tier 4 Final Engines Flywheel
3500 Engines Air Shutoff
3500B Engines for Caterpillar Built Power Modules Engine Oil Cooler Bypass and Cooling Jet Sequence Valves
3500 Engines Engine Oil Cooler Bypass and Cooling Jet Sequence Valves
C13, C15, and C18 Tier 4 Final Engines Speed/Timing Sensor
C13 Tier 4 Final Engines Solenoid Valve - Air Control Valve Gp
C13, C15, and C18 Tier 4 Final Engines Speed/Timing Sensor
Additional Procedure when Replacing the Engine, ECM, or CEM Tier 4 Engines{1000, 108D, 108F, 1901} Additional Procedure when Replacing the Engine, ECM, or CEM Tier 4 Engines{1000, 108D, 108F, 1901}
XQ125 Generator Set Fuel Tank Water and Sediment - Drain
CG137-08 and CG137-12 Engines Product Lifting
UPSB505 Uninterruptible Power Supply UPS Battery - 50Hz General Information
2011/08/26 A New Wiring Harness Is Used On Certain Commercial Engines {1408, 1900}
3516C IMO III Petroleum Engines Engine Oil Cooler - Remove
UPSB505 Uninterruptible Power Supply UPS Battery - 50Hz Component Location