Fuel System - Prime
Show/hide table
渗漏或溅溢到热表面或电气部件上的燃油会引起失火。 为防止可能的伤害,当更换燃油滤清器或油水分离器滤芯时,要将起动开关断开。 应立即将溅溢的燃油清除干净。 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 有关适于收集和盛放 Cat 产品油液的工具和用品,请参阅专门出版物, NENG2500, "Cat 代理商维修工具目录"或专门出版物, PECJ0003, "Cat 车间用品和工具目录"。 按照本地法规和要求处置所有油液。 |
Show/hide table
注意 |
---|
不要让脏物进入燃油系统。 彻底清洁将要拆开的燃油系统部件的周围区域。 在拆开的燃油系统部件上安放适当的盖。 |
Show/hide table
图 1 | g02459157 |
带注油泵的燃油滤清器 (1) 燃油细滤器 (2) 排气螺钉 (3) 燃油注油泵 |
- 将点火开关转到"断开"位置。
- 如有必要,向燃油箱加注清洁的柴油。
- 将注油阀(如有配备)转到"关闭"位置,以便向燃油系统注油。
- 将燃油滤清器的排气螺钉转动 3 整圈使其打开。 请勿取下排气螺钉。
- 将发动机转动 30 秒。 拖动发动机时,使用适当的容器盛接燃油。 让起动马达冷却 2 分钟。
注: 可以使用燃油滤清器的燃油注油泵(如有配备),而不是拖动发动机。
Show/hide table
注意 |
---|
持续盘车不要超过30秒。 再次盘车前,让起动马达先冷却2分钟。 |
- 将发动机转动 30 秒。 让起动马达冷却 2 分钟。
- 重复步骤 6,直到发动机起动并运转。
注: 如未拧紧所有接头,可能导致严重的燃油泄漏。
- 在发动机平稳运转 30 秒钟后,将注油阀转到"打开"位置。
注: 如果将注油阀留在"关闭"位置,喷油器使用寿命可能因此而缩短。
- 清除发动机部件上的任何残留燃油。
Caterpillar Information System:
UPSB505 Uninterruptible Power Supply Return to Normal Operation
C15 Petroleum Engines Diagnostic Trouble Codes
2011/03/11 Some Condensation May Be Noticed in the Crankcase of Tier 4 Engines {1000}
UPSB505 Uninterruptible Power Supply External Bypass Connection
C13 Industrial Engine Starting with Jump Start Cables - Do Not Use This Procedure in Hazardous Locations that have Explosive Atmospheres
C6.6 Industrial Engine Exhaust Manifold and Turbocharger - Remove
C6.6 Industrial Engine Exhaust Manifold and Turbocharger - Install
C13 Industrial Engine Engine Rating Definitions
CX31 On-Highway Transmission Pump Drive - Assemble
C13 Industrial Engine Reference Material
CX31 On-Highway Transmission Pump Drive - Disassemble
CX31 On-Highway Transmission Relief Valve (Torque Converter Inlet) - Remove and Install
C175-16 Petroleum Generator Set Engines Refill Capacities
C175-16 Marine Engines Fluid Recommendations
C15 Petroleum Engines Starting Motor - Inspect
C15 Petroleum Engines Turbocharger - Inspect
C175-16 Marine Engines Control Panel
C15 Petroleum Engines Plate Locations and Film Locations
2011/04/08 A New Oil Pan Gasket Is Available for Certain C15 and C18 Tier 3 Engines {1302, 7555}
2011/04/08 A New Oil Pan Gasket Is Available for Certain C15 and C18 Tier 3 Machine Engines {1302, 7555}
UPSB505 Uninterruptible Power Supply Static Switch Maintenance Connection
Procedure for Fabricating New Clean Gas Induction (CGI) Lines on Certain C15 Truck Engines{1071} Procedure for Fabricating New Clean Gas Induction (CGI) Lines on Certain C15 Truck Engines{1071}
C15 Petroleum Engines Engine Oil Pan - Remove and Install
345D, 349D and 349D2 Excavators and 345D MHPU, 349D MHPU and 349D2 MHPU Mobile Hydraulic Power Units Machine Electronic Control System E-Ceiling and Cab Avoidance - Troubleshoot