Exhaust Elbow - Remove and Install
拆卸步骤
- 如果重复使用排气弯头,请参阅专门说明书, REHS5014, "管路总成 - Tier 4 发动机柔性管再使用指南"。
- 松开卡箍组件 (1) 、 (3) 和 (5) 。
注: 在拆卸之前,标记卡箍组件 (3) 的方位。
注: 废弃卡箍组件 (1) 和 (5) 。 卡箍组件为一次性使用部件。
Show/hide table
图 1 | g02150685 |
- 通过将弯头 (2) 滑入波纹管 (4) 中获得间隙。 拆下波纹管组件。
安装步骤
- 如果重复使用排气弯头,请参阅专门说明书, REHS5014, "管路总成 - Tier 4 发动机柔性管再使用指南"。
- 距离 (X) 为 40 mm (1.6 in)。 在弯头 (2) 上做出标记 (B) 。 到弯头 (2) 端部的距离 (X) 。
Show/hide table
图 2 | g02095400 |
Show/hide table
图 3 | g02092825 |
为了便于拍照而未显示对中带 (A) 。 |
注: 对中带 (A) 会随新波纹管组件一起提供。 工具将事先安装在波纹管上。
注: 对中带 (A) 不应在步骤 11 前拆下。 工具波纹管 (4) 在安装中不得弯曲。
- 将弯头 (2) 插入波纹管中。 在不用力的前提下,应当尽可能地插入弯头。 此操作会最小化波纹管组件的总长度,从而有助于安装。
- 安装前,将两个球形卡箍组件 (1) 和 (5) 放置到波纹管组件上。
Show/hide table
图 4 | g02085353 |
为了便于拍照而未显示对中带 (A) 。 |
Show/hide table
图 5 | g02097701 |
此照片是球形卡箍组件的剖面图。 |
Show/hide table
图 6 | g02098533 |
此照片是球形卡箍组件的剖面图。 |
- 将波纹管组件放置在清洁排放模块和涡轮增压器适配器之间。 调整弯头 (2) 在卡箍组件 (3) 上滑动接头内的长度,以放置波纹管组件。
- 确认球形接头 (E) 的杯不接触球 (D) 的半径。 放置球形卡箍 (1) ,然后手动拧紧球形卡箍 (1) 。 测量距离 (Y) 和距离 (Z) 。 两个测量值应该相等。 沿球形卡箍 (1) 四周以 90° 的间隔重复测量。 必要时,调整球形卡箍 (1) 。
- 对涡轮增压器附近的球形卡箍 (5) 重复步骤 6。
- 确认标记 (B) 在卡箍组件 (3) 附近的滑动接头上不可见。
- 将球形卡箍 (1) 拧紧至扭矩为 35 ± 2 N·m (26 ± 1 lb ft)。
注: 不要利用电动工具拧紧卡箍组件 (1) 、 (3) 和 (5) 。
- 将球形卡箍 (5) 拧紧至扭矩为 35 ± 2 N·m (26 ± 1 lb ft)。
- 将对中带 (A) 从波纹管 (4) 上拆下。
- 将卡箍组件 (3) 拧紧至扭矩为 55 ± 8 N·m (41 ± 6 lb ft)。
Caterpillar Information System:
Removing the 2W-1055 Elbow {1307} Removing the 2W-1055 Elbow {1307}
C13, C15, and C18 Tier 4 Final Engines Pressure Sensor (NRS Absolute)
C9.3 Engines for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Remove and Install
G3600 Engines Maintenance Interval Schedule - G3600 Engines That Use Wellhead or Natural Gas and Have a Compression Ratio of 9.2:1
G3600 Engines Maintenance Interval Schedule - G3600 Engines That Use Natural Gas and Have a Compression Ratio of 10.5:1 or 11:1
G3600 Engines Maintenance Interval Schedule - G3600 Engines That use Bio-Gas
C4.4 Industrial Engine Fuel Injection Lines
C6.6 Industrial Engine Rocker Shaft - Disassemble
C6.6 Industrial Engine Rocker Shaft and Pushrod - Remove
Proper Maintenance of the Cooling Systems of Certain C18 Engines in Marine Applications{1350} Proper Maintenance of the Cooling Systems of Certain C18 Engines in Marine Applications{1350}
C4.4 Industrial Engine Fuel Injection Pump
C13 Engines for Caterpillar Built Machines Temperature Sensor (DPF Inlet, Flame Detect)
C18 Marine Engines Maintenance Recommendations
C18 Marine Engines Zinc Rods - Inspect/Replace
C18 Marine Engines Model View Illustrations
C9.3 Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C18 Marine Engine Cooling System Coolant (DEAC) - Change
C18 Marine Engine Cooling System Coolant (ELC) - Change
C6.6 Industrial Engine Rocker Shaft - Assemble
C6.6 Industrial Engine Rocker Shaft and Pushrod - Install
C4.4 Industrial Engine Engine Oil Pressure Sensor
C6.6 Industrial Engine Cylinder Head - Remove
C6.6 Industrial Engine Cylinder Head - Install
C4.4 Industrial Engine Speed/Timing Sensor