Crankshaft Front Seal - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 367-3534     | 油封拆卸和安装工具     | 1     |
开始:
- 拆下曲轴皮带轮。 请参阅拆解和组装, "减振器和皮带轮 - 拆卸"以了解正确步骤。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将工具 (A) 定位到曲轴前油封 (2) 上。
Show/hide table
图 1 | g01989793 |
- 逆时针转动工具 (A) 并将曲轴前油封 (2) 从前盖 (1) 上拆下。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 367-3534     | 油封拆卸和安装工具     | 1     |
B     | -     | Loctite 5900     | -     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保前盖清洁且无损坏。
- 将一层 3 mm (0.1181 in) 长连续的工具 (B) 涂抹到位置 (Y) 中的密封表面。
Show/hide table
图 2 | g02460059 |
Show/hide table
图 3 | g01990013 |
- 将新的曲轴前油封 (2) 正确定位到前盖 (1) 上的位置 (X) 。
- 将工具 (A) 定位到曲轴前油封 (2) 上。
- 使用工具 (A) 顺时针转动曲轴前油封 (2) 。
- 如果需要涂抹扭矩大于 50 N·m (37 lb ft) 的曲轴以安装曲轴前油封 (2) ,拆下曲轴前油封 (2) 。 检查曲轴前油封和前盖有无故障或损坏。
- 如有必要,重复步骤 2 至 5,以安装曲轴前油封 (2) 。
End By: 安装曲轴皮带轮。 请参阅 拆解和组装, "减振器和皮带轮 - 安装",以了解正确的步骤。。
Caterpillar Information System:
C4.4 Industrial Engine Engine Oil Pump
C6.6 Industrial Engine Vibration Damper and Pulley - Install
C6.6 Industrial Engine Vibration Damper and Pulley - Remove
2010/06/25 A New Fuse Is Now Used In Jacket Water Heater Circuit On Certain Generator Sets {1383, 1417}
2010/04/30 A New Fuse Is Now Used In Jacket Water Heater Circuit On Certain C6.6 Generator Sets {1383, 1417}
C15 and C18 Tier 4 Final Engines Exhaust Cooler (NRS) - Test
2010/05/06 Improved Remanufactured Injectors Are Now Used on Some 3408E and 3412E Industrial Engines {1251, 1254, 1290, 1713}
C13 Tier 4 Final Engines Exhaust Cooler (NRS) - Clean
C9.3 Engines for Caterpillar Built Machines Inlet Manifold - Remove and Install
Improved Jacket Water Circuit Breaker for Certain Electric Power Generators and Work Tools{1383, 1417, 1420} Improved Jacket Water Circuit Breaker for Certain Electric Power Generators and Work Tools{1383, 1417, 1420}
Improved Jacket Water Circuit Breaker for Certain Electric Power Generators{1383, 1417, 1420} Improved Jacket Water Circuit Breaker for Certain Electric Power Generators{1383, 1417, 1420}
G3520E Generator Set Engines Water Lines
C6.6 Industrial Engine Crankshaft Front Seal - Remove and Install - Crankshaft Front Seal for Heavy Duty Front Cover
C4.4 Industrial Engine Exhaust Manifold
C6.6 Industrial Engine Gear Group (Front) - Remove and Install
C4.4 Industrial Engine Engine Oil Filter Base
C6.6 Industrial Engine Gear Group (Front) - Remove and Install - Heavy Duty Gear Group (Front)
C6.6 Industrial Engine Idler Gear - Remove
C6.6 Industrial Engine Idler Gear - Install
C6.6 Industrial Engine Housing (Front) - Remove
C7 On-highway Engine Maintenance Interval Schedule - Engines with a Shallow Oil Sump
C6.6 Industrial Engine Housing (Front) - Remove - Heavy Duty Housing (Front)
C4.4 Industrial Engine Engine Oil Cooler
C6.6 Industrial Engine Housing (Front) - Install