Wheel, Brake and Suspension (Front) - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 174-9245     | 前支柱托架     | 1     |
B     | B4C-5593     | 防粘结剂     | -     |
C     | 334-8336     | 反作用臂     | 1     |
D     | 334-8335     | 反作用臂     | 1     |
- 安装键 (13) 。
Show/hide table
图 1 | g02139373 |
- 使用工具 (A) 以安装前轮、制动器和悬架油缸 (8) 。 前轮、制动器和悬架油缸 (8) 的重量约为 8000 kg (17637 lb)。
Show/hide table
图 2 | g02139365 |
- 将工具 (B) 涂敷到新螺栓 (12) 、新螺栓 (10) 和垫圈上。 将螺栓 (12) 和螺栓 (10) 安装到悬架油缸的两侧。
Show/hide table
图 3 | g02139368 |
- 使用工具 (C) 以便保留螺栓 (12) 。 拧紧螺母 (11) 至扭矩为 1000 ± 100 N·m (738 ± 74 lb ft)。 将螺母 (11) 再转动 120° ± 20° ()。
- 使用工具 (D) 以便保留螺栓 (10) 。 拧紧螺母 (9) 至扭矩为 800 ± 80 N·m (590 ± 59 lb ft)。 将螺母 (9) 再转动 120° ± 20° ()。
- 使用适当的起吊设备以便定位转向臂 (7) 。 转向臂 (7) 的重量约为 696 kg (1534 lb)。 安装螺栓 (8) 。
Show/hide table
图 4 | g02139310 |
- 连接线束组件 (6) 和安装接线紧固件。
Show/hide table
图 5 | g02139294 |
- 连接润滑脂软管组件 (5) 。
Show/hide table
图 6 | g02139271 |
- 连接软管组件 (4) 。
Show/hide table
图 7 | g02139263 |
- 连接软管组件 (3) 和软管组件 (2) 。 安装夹子 (1) 。
Show/hide table
图 8 | g02139258 |
- 向行车和停车制动器中加满油。 请参阅操作和保养手册, "容量 - 加注"。
- 排出行车和停车制动器中的空气。 请参阅测试和调整, "制动系统空气 - 排除"。
Show/hide table
制动液压系统的机油中存在空气会造成人员伤亡。 系统中存在空气会影响制动器完全发挥作用,且机器上的车轮可能无法停止。 要使制动液压系统正常工作,其中的机油不得存在空气。 |
- 向前轮注油。 请参阅操作和保养手册, "前轮油 – 更换"。
- 向液压油箱中加注机油。 请参阅操作和保养手册, "容量 - 加注"。
- 给悬架油缸充油和氮。 请参阅专门说明书, SEHS9411, "维修非公路卡车的悬架油缸"。
Show/hide table
进行维修之前,应阅读悬挂油缸上的所有警告标签。 释放氮气压力之前,必须先将机器停在平稳的地面上。 释放所有氮气压力之前,切勿对悬挂油缸中的机油进行检查。 除非活塞杆完全缩回,且所有氮气压力都已排尽,否则请勿卸下悬挂油缸上的任何阀门、盖子或螺塞。 悬挂油缸充油、排放或测试和调整过程中,或者提升或降低机器时,不要靠近机器。 机器突然向上或向下移动可能会导致净空高度迅速改变。 忽视此警告可能会导致人身伤亡。 |
End By: 安装前轮胎和轮辋。
Caterpillar Information System:
797 Off-Highway Truck Wheel, Brake and Suspension (Front) - Remove
797 Off-Highway Truck Front Suspension (Cylinder) - Install
797 Off-Highway Truck Front Suspension (Cylinder) - Remove
C4.4 Industrial Engine Emissions Certification Film
C18 Marine Engine Engine Oil Level - Check
797F and 797F XQ Off-Highway Trucks Machine Systems Accumulator (Steering) - Remove and Install
349F and 352F Excavators Hydraulic System Travel on Level Ground - Test - Optional Test
797F and 797F XQ Off-Highway Trucks Machine Systems Air Dryer - Remove and Install
C4.4 Industrial Engine Plate Locations and Film Locations
C6.6 Industrial Engine Fuel Injection
2010/11/22 New Connecting Rod for the C6.6 Engine {1225}
C4.4 Industrial Engine Engine Description
XQ400 Power Module Burn Prevention
3176C and 3196 Marine Engines Engine Starting
C15 and C18 Engines Fuel and the Effect from Cold Weather
Procedure to Repair the Pump for the Aftertreatment Regeneration Device (ARD) {1258} Procedure to Repair the Pump for the Aftertreatment Regeneration Device (ARD) {1258}
C27 and C32 Engines for Caterpillar Built Machines Lubrication System
C18 Marine Engine Sensors and Electrical Components
C15 and C18 Engines Electrical System
C6.6 Industrial Engine Basic Engine
C6.6 Industrial Engine Air Inlet and Exhaust System
C4.4 Industrial Engine Glossary of Electronic Control Terms
C6.6 Industrial Engine Electronic Control System
C6.6 Industrial Engine Power Sources