Pump Drive - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7575     | 连杆支架     | 3     |
B     | 1P-2420     | 变速箱修复台     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 检查 O 形密封圈、密封件和垫片。 更换磨损或损坏的 O 形密封圈、密封件和垫片。
注: 利用所密封的润滑剂润滑 O 形密封圈。
- 安装 O 形密封圈 (6) 。
Show/hide table
图 1 | g01843134 |
- 使用工具 (A) 和适当的起吊设备安装泵驱动装置 (5) 。 泵驱动装置 (5) 的重量约为 31 kg (70 lb)。 安装螺栓 (4) 。 将螺栓 (4) 拧紧至扭矩 100 ± 20 N·m (74 ± 15 lb ft)。
Show/hide table
图 2 | g01843147 |
- 安装护罩组件 (3) ,然后安装螺栓 (2) 。 将螺栓拧紧至 28 ± 7 N·m (21 ± 5 lb ft)。
Show/hide table
图 3 | g01843143 |
- 利用工具 (A) 和适当的起吊设备将变矩器壳体 (1) 从工具 (B) 上拆下。 变矩器壳体 (1) 的重量大约为 134 kg (295 lb)。
Show/hide table
图 4 | g01843141 |
End By: 安装变矩器。 请参阅 拆解和组装, "变矩器 - 安装"。
Caterpillar Information System:
CX31-P600 Petroleum Transmission Well Servicing Pump Drive - Remove
C15 and C18 Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
CX31-P600 Petroleum Transmission Well Servicing Control Manifold - Install
CX31-P600 Petroleum Transmission Well Servicing Control Manifold - Remove
CX31-P600 Petroleum Transmission Transmission Hydraulic Control - Side PTO, No Retarder
CX31-P600 Petroleum Transmission Safety Messages
CX31-P600 Petroleum Transmission Well Servicing Torque Converter - Install
CX31-P600 Petroleum Transmission Well Servicing Torque Converter - Remove
C15 and C18 Industrial Engines Turbocharger - Remove and Install
C15 and C18 Industrial Engines Fuel Transfer Pump - Remove and Install
2009/03/23 Replacement Panels for the Generator Set Enclosures {7274}
795F AC and 795F AC XQ Off-Highway Trucks Electrical Shutdown and Voltage Discharge
784C and 785C Off-Highway Truck/Tractors System Pressure Release
795F and 795F AC XQ Off-Highway Truck Steering System Metering Pump (Steering)
CX31-P600 Petroleum Transmission Well Servicing Gear Pump (Torque Converter and Transmission) - Remove
CX31-P600 Petroleum Transmission Well Servicing Gear Pump (Torque Converter and Transmission) - Install
CX31-P600 Petroleum Transmission Well Servicing Oil Filter and Base (Power Train) - Remove and Install
795F AC and 795F AC XQ Off-Highway Trucks Electric Retarder - Clean - Inlet Screen
CX31-P600 Petroleum Transmission Plate Locations and Film Locations
CX31-P600 Petroleum Transmission Well Servicing Speed Sensor (Transmission) - Remove
CX31-P600 Petroleum Transmission Well Servicing Speed Sensor (Transmission) - Install
CX31-P600 Petroleum Transmission Component Location
2009/06/01 A New Crankshaft Gear, Cluster Gear Assembly, and Crankshaft Assembly Are Now Used {1151, 1162, 1202, 1206}
C15 and C18 Engines for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Disassemble