Gear Pump (Torque Converter and Transmission) - Install
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 检查 O 形密封圈、密封件和垫片。 更换磨损或损坏的 O 形密封圈、密封件和垫片。
注: 利用所密封的润滑剂润滑 O 形密封圈。
- 安装 O 形密封圈 (25) 。
Show/hide table
图 1 | g01844433 |
- 安装齿轮泵 (24) 。 安装螺栓 (23) 。 拧紧螺栓 (23) 上到扭矩为 55 ± 10 N·m (41 ± 7 lb ft)。
Show/hide table
图 2 | g01844423 |
- 安装壳体 (22) ,然后安装螺栓 (21) 。 用 55 ± 10 N·m (40 ± 7 lb ft)的扭矩拧紧螺栓 (21) 。 安装管组件 (20) 和管组件 (19) 。
注: 将管组件 (20) 上紧到 42 ± 2 N·m (31 ± 2 lb ft) 的扭矩。 将管组件 (19) 上紧到 172.5 ± 7.5 N·m (127 ± 6 lb ft) 的扭矩。
Show/hide table
图 3 | g01844421 |
- 安装密封 (18) 、O 形密封圈 (17) 和 O 形密封圈 (16) 。
Show/hide table
图 4 | g01844416 |
- 安装油底壳 (15) 。 安装螺栓 (14) 和螺栓 (13) 。 拧紧螺栓 (14) 至扭矩为 28 ± 7 N·m (21 ± 5 lb ft)。
Show/hide table
图 5 | g01844394 |
Show/hide table
图 6 | g01841313 |
- 将两个带有 X 标记的螺栓 (13) 拧紧至扭矩为 28 ± 7 N·m (21 ± 5 lb ft)。
- 将其余螺栓 (13) 拧紧至扭矩为 55 ± 10 N·m (41 ± 8 lb ft)。
- 连接线束组件 (12) 。
Show/hide table
图 7 | g01843774 |
- 安装护罩 (11) 。 安装螺栓 (10) 。 将螺栓 (10) 上紧到 28 ± 7 N·m (21 ± 5 lb ft) 的扭矩。
Show/hide table
图 8 | g01843733 |
- 安装滤网 (9) 和磁性滤清器 (8) 。
Show/hide table
图 9 | g01843642 |
- 安装 O 形密封圈 (7) 。
Show/hide table
图 10 | g01843639 |
- 安装盖 (6) 和螺栓 (5) 。 用 28 ± 7 N·m (21 ± 5 lb ft) 的扭矩拧紧螺栓 (5) 。
Show/hide table
图 11 | g01843638 |
- 安装输出轴 (4) 和轴承组件 (3) 。 安装挡圈 (2) 和挡圈 (1) 。
Show/hide table
图 12 | g01843618 |
End By: 将变速箱连接至发动机。 请参阅 拆解和装配, "发动机、变矩器和变速箱 - 连接"。
Caterpillar Information System:
CX31-P600 Petroleum Transmission Well Servicing Gear Pump (Torque Converter and Transmission) - Remove
795F and 795F AC XQ Off-Highway Truck Steering System Metering Pump (Steering)
784C and 785C Off-Highway Truck/Tractors System Pressure Release
CX31-P600 Petroleum Transmission Well Servicing Pump Drive - Install
CX31-P600 Petroleum Transmission Well Servicing Pump Drive - Remove
C15 and C18 Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
CX31-P600 Petroleum Transmission Well Servicing Control Manifold - Install
CX31-P600 Petroleum Transmission Well Servicing Control Manifold - Remove
CX31-P600 Petroleum Transmission Transmission Hydraulic Control - Side PTO, No Retarder
CX31-P600 Petroleum Transmission Safety Messages
CX31-P600 Petroleum Transmission Well Servicing Torque Converter - Install
CX31-P600 Petroleum Transmission Well Servicing Torque Converter - Remove
CX31-P600 Petroleum Transmission Well Servicing Oil Filter and Base (Power Train) - Remove and Install
795F AC and 795F AC XQ Off-Highway Trucks Electric Retarder - Clean - Inlet Screen
CX31-P600 Petroleum Transmission Plate Locations and Film Locations
CX31-P600 Petroleum Transmission Well Servicing Speed Sensor (Transmission) - Remove
CX31-P600 Petroleum Transmission Well Servicing Speed Sensor (Transmission) - Install
CX31-P600 Petroleum Transmission Component Location
2009/06/01 A New Crankshaft Gear, Cluster Gear Assembly, and Crankshaft Assembly Are Now Used {1151, 1162, 1202, 1206}
C15 and C18 Engines for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Disassemble
CX31 On-Highway Transmission Power Train Retarder - Remove
CX31 On-Highway Transmission Power Train Retarder - Install
2013/01/28 Improved Hardware for the Camshaft Thrust Plate Is Used in Certain 3500 Engines {1204, 1210}
C15 and C18 Industrial Engines Exhaust Manifold - Remove and Install