Torque Converter - Install
安装步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 327-9235 | 密封安装工具 | 1 |
| B | 138-7575 | 连杆支架 | 3 |
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 检查 O 形密封圈、密封件和垫片。 更换磨损或损坏的 O 形密封圈、密封件和垫片。
注: 利用所密封的润滑剂润滑 O 形密封圈。
- 利用工具 (A) 将唇形密封 (4) 安装到图示的深度。
Show/hide table
 | |
| 图 1 | g01967553 |
Show/hide table
 | |
| 图 2 | g01967573 |
- 利用工具 (B) 和适当的起吊设备安装变矩器 (3) 。 变矩器 (3) 的重量约为 91 kg (200 lb)。
Show/hide table
 | |
| 图 3 | g01967539 |
- 安装螺栓 (2) 。 拧紧螺栓 (2) 至扭矩为 285 ± 15 N·m (210 ± 11 lb ft)。 安装螺塞 (1) 。 拧紧螺塞 (1) ，扭矩为 285 ± 15 N·m (210 ± 11 lb ft)。
Show/hide table
 | |
| 图 4 | g01967535 |
Show/hide table
 | |
| 图 5 | g01967534 |
End By: 将变速箱连接至发动机。 请参阅 拆解和装配, "发动机、变矩器和变速箱 - 连接"。
Caterpillar Information System:
CX31-P600 Petroleum Transmission Well Servicing Torque Converter - Remove
C15 and C18 Industrial Engines Turbocharger - Remove and Install
C15 and C18 Industrial Engines Fuel Transfer Pump - Remove and Install
2009/03/23 Replacement Panels for the Generator Set Enclosures {7274}
795F AC and 795F AC XQ Off-Highway Trucks Electrical Shutdown and Voltage Discharge
C13 Engine for Combat and Tactical Vehicles Aftercooler - Test
C175-16 Petroleum Generator Set Engines Maintenance Recommendations
2009/03/09 Hard Starting of 3456 and C15 Generator Sets {1261, 1263}
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks ECM - Replace
CX31-P600 Petroleum Transmission Specifications
XQ175 Rental Generator Set Generator Lead Connections
CX31-P600 Petroleum Transmission Well Servicing Transmission and Torque Converter - Connect
CX31-P600 Petroleum Transmission Safety Messages
CX31-P600 Petroleum Transmission Transmission Hydraulic Control - Side PTO, No Retarder
CX31-P600 Petroleum Transmission Well Servicing Control Manifold - Remove
CX31-P600 Petroleum Transmission Well Servicing Control Manifold - Install
C15 and C18 Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
CX31-P600 Petroleum Transmission Well Servicing Pump Drive - Remove
CX31-P600 Petroleum Transmission Well Servicing Pump Drive - Install
784C and 785C Off-Highway Truck/Tractors System Pressure Release
795F and 795F AC XQ Off-Highway Truck Steering System Metering Pump (Steering)
CX31-P600 Petroleum Transmission Well Servicing Gear Pump (Torque Converter and Transmission) - Remove
CX31-P600 Petroleum Transmission Well Servicing Gear Pump (Torque Converter and Transmission) - Install
CX31-P600 Petroleum Transmission Well Servicing Oil Filter and Base (Power Train) - Remove and Install