Fan Drive Bearing - Lubricate
Show/hide table
| |
| 图 1 | g01694159 |
|
风扇驱动系统上有四个润滑脂加油嘴。 | |
应在发动机试运行时检查风扇驱动系统。 应在发动机试运行时润滑风扇驱动系统。 在以下一种或多种环境下运行的发动机应进行更频繁的润滑：温度过高, 污物过多 和 湿度过高。
对于风扇驱动系统的使用寿命，按以下周期检查风扇驱动系统，以先到者为准。
- 500 工作小时
- 12 个月
检查风扇驱动装置有无磨损或损坏。 如果轴松动，检查内部部件。
在风扇驱动系统使用寿命期内，按以下周期润滑风扇驱动系统，以先到者为准：
- 500 工作小时
- 12 个月
用 Cat 多功能润滑脂或类似属性的润滑脂润滑加油嘴。 在轴承转动的同时润滑轴承。 清洁润滑脂已通过密封件排出时停止润滑。 不要考虑使用的润滑脂量。
Caterpillar Information System:
No Starboard Throttle Signal{3065, 4490} No Starboard Throttle Signal{3065, 4490}
Prevention of Leaks in the C18 Marine Heat Exchanger Frame {1379, 1395} Prevention of Leaks in the C18 Marine Heat Exchanger Frame {1379, 1395}
C18 Fire Pump Industrial Engine Water Pump - Remove
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Aftercooler - Remove and Install
R250 Automatic Voltage Regulator General Information
Parts for Updating Early 3406E Aftercooler Cores{1063} Parts for Updating Early 3406E Aftercooler Cores{1063}
R250 Automatic Voltage Regulator High Voltage
Upgrade to Air/Fuel Ratio Control, Nitrogen Oxide Sensor, and a Single Turbocharger for Enhanced Performance of G3508 Engines{1000, 1052, 1270, 191N} Upgrade to Air/Fuel Ratio Control, Nitrogen Oxide Sensor, and a Single Turbocharger for Enhanced Performance of G3508 Engines{1000, 1052, 1270, 191N}
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Exhaust Elbow - Remove and Install
320D and 323D Excavators Machine System Specifications Grease Lines
3500B Engines for Caterpillar Built Power Modules Turbocharger
3500B Generator Set Engines Turbocharger
R250 Automatic Voltage Regulator No Voltage
C175-16 Petroleum Generator Set Engines Model View Illustrations
R250 Automatic Voltage Regulator Low Voltage
R250 Automatic Voltage Regulator Load Acceptance Module Operation
C18 Fire Pump Industrial Engine Water Pump - Install
R250 Automatic Voltage Regulator Wiring Diagram
C175-16 Petroleum Generator Set Engines Engine Oil and Filter - Change
R250 Automatic Voltage Regulator Knee Frequency - Adjust - For Constant Volts Per Hertz Operation
C18 Fire Pump Industrial Engine Water Temperature Regulator Housing - Remove and Install
C18 Fire Pump Industrial Engine Engine Support (Front) - Remove and Install
C18 Fire Pump Industrial Engine Flywheel - Remove - Adapter
Updating Engines that are Equipped with a Heated Nozzle for the Caterpillar Regeneration System (CRS){108B, 108E, 108M} Updating Engines that are Equipped with a Heated Nozzle for the Caterpillar Regeneration System (CRS){108B, 108E, 108M}