Bucket Cylinder - Remove and Install
参考: 专门说明书, "目视维修步骤 - 颜色和符号" M0066576。
Show/hide table
| |
| 图 1 | g06237644 |
Show/hide table
 |
|
液压油的压力或滚热的油会对人员造成伤害。 发动机停机之后，液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前，如果不事先释放压力，可能会造成严重伤害。 拆卸任何部件或管路之前，确保所有附件均已降下，且机油已冷却。 |
Show/hide table
| |
| 图 2 | g06237652 |
|
释放液压系统压力。 | |
Show/hide table
| |
| 图 3 | g06237655 |
|
排放液压系统油。 请参阅操作和保养手册, 液压系统油 - 更换，以了解排放和加注步骤。 | |
Show/hide table
| |
| 图 4 | g06238130 |
Show/hide table
| |
| 图 5 | g06238151 |
|
GC 机型上的铲斗油缸重量约为 | |
Show/hide table
| |
| 图 6 | g06238171 |
- 按与拆卸相反的顺序安装铲斗油缸。
Caterpillar Information System:
D6 Track-Type Tractor Systems General Information (Hydraulic System)
986K Wheel Loader Bucket Wear Plates - Inspect/Replace
986K Wheel Loader Bucket Stops - Inspect/Replace
New Water Pump Seal and Pumps Used on Certain 3500, G3500, and C175 Engines {1361, 7555} New Water Pump Seal and Pumps Used on Certain 3500, G3500, and C175 Engines {1361, 7555}
992K Wheel Loader System Schematic
336, 336 GC and 340 Excavator Systems Pump Control (Main Hydraulic) - Main Pump Regulator
MD6250 Rotary Drill Capacities (Refill)
D9T Track-Type Tractor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} D9T Track-Type Tractor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
D9T Track-Type Tractor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} D9T Track-Type Tractor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
336, 336 GC and 340 Excavator Systems Main Hydraulic Pump
525D, 535D, 545D and 555D Wheel Skidders Machine Systems Arch Cylinder - Remove and Install
525D, 535D, 545D and 555D Wheel Skidders Machine Systems Pilot Oil Accumulator (Dead Engine Lower) - Remove and Install
330 GC and 330 Excavator Joystick Controls
A New Milling Process Has Improved the Cylinder Block Deck Surface Finish on Certain C15 and C18 Machine Engines {0677, 1201} A New Milling Process Has Improved the Cylinder Block Deck Surface Finish on Certain C15 and C18 Machine Engines {0677, 1201}
330 GC and 330 Excavator Declaration of Conformity
Track Joint Inspection and Lubrication Procedure Using 8T-3115 Lubricator Gp - Portable Track {0646, 4169, 4170} Track Joint Inspection and Lubrication Procedure Using 8T-3115 Lubricator Gp - Portable Track {0646, 4169, 4170}
Procedure to Reinforce the Front Frame Axle Pads Is Now Available for Certain 982M Medium Wheel Loaders {0679, 3268, 3278, 3282} Procedure to Reinforce the Front Frame Axle Pads Is Now Available for Certain 982M Medium Wheel Loaders {0679, 3268, 3278, 3282}
C32 Marine Engines Auxiliary Water Pump - Install
320GC, 320 and 323 Excavators Machine Systems Load Control Valve (Stick Cylinder) - Remove and Install
Requirements for Installation of Cat Production Measurement (CPM) Payload Control Kit on 926M, 930Mand 938M Wheel Loaders {7494} Requirements for Installation of Cat Production Measurement (CPM) Payload Control Kit on 926M, 930Mand 938M Wheel Loaders {7494}
986K Wheel Loader Transmission Oil Level - Check
986K Wheel Loader Transmission Oil - Change
MD6200 Rotary Drill Engine Starting with Auxiliary Start Receptacle - If Equipped
986K Wheel Loader Articulation Bearings - Lubricate