C32 Marine Engines Caterpillar


Auxiliary Water Pump - Install

Usage:

C32 AX2

安装步骤

注: 检查所有 O 形圈、密封件和垫片是否磨损和损坏。 根据需要加以更换。



    图 1g06250175

  1. 将适当起吊设备连在辅助水泵 (6) 上。 辅助水泵 (6) 的重量约为 。 25 kg (55 lb)

  2. 定位辅助水泵 (6),然后安装四个螺栓 (5)。

  3. 定位弯管并安装四个螺栓 3 和 2。 () ()

  4. 连接螺塞 (4)。


    图 2g06250159

  5. 安装两个螺栓 (1)。

Caterpillar Information System:

Procedure to Reinforce the Front Frame Axle Pads Is Now Available for Certain 982M Medium Wheel Loaders {0679, 3268, 3278, 3282} Procedure to Reinforce the Front Frame Axle Pads Is Now Available for Certain 982M Medium Wheel Loaders {0679, 3268, 3278, 3282}
Track Joint Inspection and Lubrication Procedure Using 8T-3115 Lubricator Gp - Portable Track {0646, 4169, 4170} Track Joint Inspection and Lubrication Procedure Using 8T-3115 Lubricator Gp - Portable Track {0646, 4169, 4170}
330 GC and 330 Excavator Declaration of Conformity
A New Milling Process Has Improved the Cylinder Block Deck Surface Finish on Certain C15 and C18 Machine Engines {0677, 1201} A New Milling Process Has Improved the Cylinder Block Deck Surface Finish on Certain C15 and C18 Machine Engines {0677, 1201}
330 GC and 330 Excavator Joystick Controls
320GC, 320 and 323 Excavators Machine Systems Bucket Cylinder - Remove and Install
D6 Track-Type Tractor Systems General Information (Hydraulic System)
986K Wheel Loader Bucket Wear Plates - Inspect/Replace
986K Wheel Loader Bucket Stops - Inspect/Replace
New Water Pump Seal and Pumps Used on Certain 3500, G3500, and C175 Engines {1361, 7555} New Water Pump Seal and Pumps Used on Certain 3500, G3500, and C175 Engines {1361, 7555}
992K Wheel Loader System Schematic
336, 336 GC and 340 Excavator Systems Pump Control (Main Hydraulic) - Main Pump Regulator
320GC, 320 and 323 Excavators Machine Systems Load Control Valve (Stick Cylinder) - Remove and Install
Requirements for Installation of Cat Production Measurement (CPM) Payload Control Kit on 926M, 930Mand 938M Wheel Loaders {7494} Requirements for Installation of Cat Production Measurement (CPM) Payload Control Kit on 926M, 930Mand 938M Wheel Loaders {7494}
986K Wheel Loader Transmission Oil Level - Check
986K Wheel Loader Transmission Oil - Change
MD6200 Rotary Drill Engine Starting with Auxiliary Start Receptacle - If Equipped
986K Wheel Loader Articulation Bearings - Lubricate
D6 Track-Type Tractor Systems Control Valve (Implement)
973K Track-Type Loader Engine Supplement Fan - Remove and Install
336, 336 GC and 340 Excavator Systems General Information (Boom System)
525D, 535D, 545D and 555D Wheel Skidders Machine Systems Boom Cylinder - Remove and Install
D7E Track-Type Tractor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} D7E Track-Type Tractor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
D7E Track-Type Tractor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565} D7E Track-Type Tractor TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.