Troubleshooting Procedure for Seat Belt Retraction on Certain Wheel Loaders {7307, 7312, 7327}
- Wheel Loader
- 924K (S/N: KW41-UP; ENC1-UP; HJF1-UP; PWR1-UP; SNZ1-UP)
- 926M (S/N: LTE1-UP)
- 930K (S/N: DYB1-UP; EYE1-UP; FRK1-UP; P3K1-UP; RHN1-UP)
- 930M (S/N: KTG1-UP; HEY1-UP)
- 938K (S/N: W8K1-UP; SWL1-UP; REP1-UP; XXT1-UP; HFW1-UP)
- 938M (S/N: J3R1-UP)
- 926M (S/N: LTE1-UP)
Introduction
This Special Instruction provides troubleshooting procedures for seat belt retraction on certain Wheel loaders.
Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.
For Web Twisting:
- Check for twisted web in front and rear windows of the housing.
- To clear a twist, push or pull the web to loosen it on the retractor spool.
- Side to side movement of the belt may also clear partial twist in the web.
Show/hide table
Illustration 1 | g06293485 |
For Reverse Lock:
- Check for reverse lock.
- Mount the belt in the seat belt housing.
- Pull the web forcefully to tighten it on the retractor spool, which allows more web to be wrapped on spool when it retracts.
- Slowly allow the web to retract back into the retractor housing.
For Orientation of Seat Belt Housing:
Show/hide table
Illustration 2 | g06196968 |
(A) 35 ± 5 degree |
- Orient the seat belt housing to an angle of 35 ± 5 degree from vertical position for optimum operation.
Caterpillar Information System:
A New Troubleshooting Procedure Is Now Available for the Seat Belt Retraction on Certain Wheel Loaders {7307, 7312, 7327} A New Troubleshooting Procedure Is Now Available for the Seat Belt Retraction on Certain Wheel Loaders {7307, 7312, 7327}
320 GC, 320 and 323 Excavator Joystick Controls
Improved Routing for Breather Pipe Is Now Used on Certain Wheel Feller Bunchers and Wheel Skidders {1317} Improved Routing for Breather Pipe Is Now Used on Certain Wheel Feller Bunchers and Wheel Skidders {1317}
C9.3B Aftertreatment Systems Sensor Signal (Analog, Active) - Test - Aftertreatment
C9.3B Aftertreatment Systems Sensor Calibration Required - Test - Aftertreatment
320GC Excavator Engine Supplement Water Separator and Fuel Priming Pump - Remove and Install
Electronic Unit Injectors on Certain C4.4 Machine Engines {1251, 1254, 1290} Electronic Unit Injectors on Certain C4.4 Machine Engines {1251, 1254, 1290}
990K Wheel Loader Systems Joystick Control and Mounting
AD 22 Underground Articulated Truck Steering Systems System Pressure - Release
AD22 Underground Articulated Truck Frame and Body Support Pads - Clean/Inspect
AD22 Underground Articulated Truck Capacities (Refill)
New Flywheel Housing Used on Certain 844K and 990K Machine Engines {1157} New Flywheel Housing Used on Certain 844K and 990K Machine Engines {1157}
C9.3B Engines for Caterpillar Built Machines Atmospheric Pressure Sensor - Remove and Install
Bluetooth Operator ID and Machine Security System (MSS) Configuration - Machine Security System
C27 and C32 Tier 4 Final Marine Engines Valve Mechanism Cover
C9.3B Engines for Caterpillar Built Machines Coolant Temperature Sensor - Remove and Install
320 GC, 320 and 323 Excavator Machine Systems Specifications Relief Valve (Line)
C9.3B Engines for Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
336 and 336 GC Excavator Selective Catalytic Reduction Warning System
320 GC, 320 and 323 Excavator Machine Security System
320 GC, 320 and 323 Excavator Machine Systems Specifications Boom Cylinder
A New O-Ring Seal in the Implement Lines group is Now Used on Certain 631K and 637K Wheel Tractor-Scrapers {5051, 5057} A New O-Ring Seal in the Implement Lines group is Now Used on Certain 631K and 637K Wheel Tractor-Scrapers {5051, 5057}
C9.3B Engines for Caterpillar Built Machines Crankcase Pressure Sensor - Remove and Install
990K Wheel Loader and 844K Wheel Dozer Machine Systems Piston Pump (Brake, Steering) - Disassemble